+ Reply to Thread
Page 120 of 166 FirstFirst ... 2070110118119120121122130 ... LastLast
Results 1,191 to 1,200 of 1659

Thread: Mod your Beresford 7520

  1. #1191
    Join Date: Nov 2008

    Location: Latvia

    Posts: 51
    I'm Gints.

    Default

    Quote Originally Posted by larry View Post
    Hi,

    I have 2 THS4032 installed on my TC 7520. I brought is on eBay from tirna electronic. I am using the build in headphone amp to drive HD600. When lisenting at low volume at 9 o'clock. There is noticetable distortin in the sound. It seem to be unstable to me. But when listening at a higher volume. let's say 11 o'clock. The distorion is minimise but the distortion is still there but less noticetable. I try using toslink(desktop pc) and USB(netbook) both have the same problem, meaning my source is ok. So what is the real problem I have?
    Just my guessing. I am sure you lowered amp board (otherwise you cannot close lid) and now it is very close or almost touching capacitors below it. Put some insulation between, maybe that helps.

  2. #1192
    Join Date: Aug 2009

    Location: New Jersey, USA

    Posts: 85

    Default

    Out of curiosity, if each opamp is for a different output, then how does having two of the same opamps installed change the sound vs having 1 of them installed?
    Anthony

  3. #1193
    Join Date: Nov 2008

    Location: Latvia

    Posts: 51
    I'm Gints.

    Default

    Quote Originally Posted by Sensimilia View Post
    The THS4032 is a very good line driver, so it will handle even hard to control interconnecting leads between DAC and amplifier with a lot of control.
    I have about 10 metres long cable from dac to amplifier. Is THS4032 would be better for line output in this case then LM4562HA?

  4. #1194
    Join Date: Nov 2008

    Location: Latvia

    Posts: 51
    I'm Gints.

    Default

    Quote Originally Posted by Sensimilia View Post
    But the THS4032 needs the caps next to it on the PCB, unless you want a lot of RF break through.
    STan
    What was a reason for cap on THS4032 from Tirna. That was not same as caps on the PCB? And put next to the chip only because those on PCB are too far away?
    Last edited by Gints; 05-08-2009 at 18:08.

  5. #1195
    Join Date: Jul 2009

    Location: Singapore

    Posts: 14
    I'm Larry.

    Default

    After some troubleshooting, I heard distortion from the same spot of a song. Can I say that my source is the culprit? 2 4032 sound very detail. It really reveal my song.

  6. #1196
    Join Date: Feb 2008

    Location: http://www.homehifi.co.uk

    Posts: 6,289

    Default

    My DACs are clinical, so distortion in the source material is going to rear its ugly head.

  7. #1197
    Join Date: Aug 2009

    Location: New Jersey, USA

    Posts: 85

    Default

    Has anyone tried to put a discrete opamp in a Beresford?
    Anthony

  8. #1198

    Default

    hey guys, i've been away for a while...so any news on the Caiman and when it can be expecting to be released?

    Stan, would it be possible for the Caiman be sent out on loan for a review? i'd really like to test it out.
    Alan

  9. #1199
    Join Date: Aug 2009

    Location: New Jersey, USA

    Posts: 85

    Default

    Quote Originally Posted by AudioFile808 View Post
    hey guys, i've been away for a while...so any news on the Caiman and when it can be expecting to be released?

    Stan, would it be possible for the Caiman be sent out on loan for a review? i'd really like to test it out.
    I believe they were released, as I purchased one.
    Anthony

  10. #1200
    Join Date: Feb 2008

    Location: http://www.homehifi.co.uk

    Posts: 6,289

    Default

    Quote Originally Posted by therockst4r View Post
    Has anyone tried to put a discrete opamp in a Beresford?
    I did. I tried a set of Burson discrete opamps. The results were:
    1. It didn't work
    2. The case couldn't close

    Added to that, the distortion figures for the U$100 Burson discrete opamps are 0.001%, compared to the U$5 LM4562 0.00003%.

    If you are however hell bent on going discrete, even though the sound will be more distorted than the LM4562, let us know how you get on.

    Stan

+ Reply to Thread

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •