Location: Athens
Posts: 268
I'm Dimitris.
I like IKEA for its wide range of easy to use parts, but sometimes you just have to look a bit further for a much nicer option.
A couple of years back I bought a rough plank of wenge wood that was 3cm thick, 45cm wide and 3meters long for about 100 euros from a local wood trader.
Mahogany and Maple were about the same price for 50mm thick planks but it was a bit difficult to find a nice piece that was wide enough.
There were also cheaper and more expensive woods to choose from, and the planks were up to ~60mm thick.
And I guess a bigger country may offer a wider wood variety for better prices.
A local carpenter should be able to procure, plane and square an infinitely more beautiful board for not much more than the IKEA one.
OK the IKEA has vertical wood pieces glued in a sandwich, but its effectiveness is debatable.
If you have a few tools (circular saw and power plane) to do it yourself, then it will be even cheaper.
You will have to pay for the extra bulk wood though, but you will have enough to build nice platforms for your other devices too
Sources: Modified SL1200 MK2, Salas folded RIAA, Phonoclone, VSPS, Shelter 501 MK2, Modified Pioneer P6D6 as transport, Shigaclone transport, Peter Daniel NOS DAC.
Amplification: Custom 211 Monoblocks, Electrocompaniet AW120, Audio Research VS110, Gainclone
Loudspeakers: Tannoy Turnberry, PBN Montana EP Signature
Cables/stands: Tempflex ribbon and Twinax cables
Other: Promitheus Signature Passive Attenuator, Custom JFET - transformer preamp.
Hi, Dimitris. Thanks for the commnets. The IKEA board is very cheap at approx 13 Euros and is already made. I'm sure that better boards exist and probably give better results, but, I'm more than happy in the knowledge I don't have to find a carpenter, store the wood off cuts or pay 100Euros for a large piece of wood. I'm extremely happy with the small but beneficial improvement that the IKEA board has given to my 1210.
SS
CD Teac VRDS25X(Audiotuned) DECK 1210 Mat Crystal Audio Mods MN Base/Bearing/Platter+Ebony armboard Feet Isonoe PSU Paul Hynes SR7EHD-27XL/DCSXL Ag DC lead/3 Stage Regs/Recap PCB+No Pitch/Strobe/Light ARM SME V(Kondo Ag Rewire&Tags) MC Cadenza Black FGS CABLES Arm Yannis SPD-4 IC Yannis 222 Litz+Ag bullets Power WAR PRE ATC SCA2 SPEAKERS ATC 50ASL STANDS Atacama PHONO Sugden Masterclass PA4 SUT Ortofon ST80SE POWER PSAudio P10
VALVE
PRE Croft Epoch(Modded) AMP Sondex S100 (Modded) SPEAKERS Tannoy 15"MG+RFC Warwick cabs+ Ref XO + Batpure supertweeters DECK Garrard 301 Mat Teunto Bearings 401(Bastin) Plinth Bamboo Arms 3009/3012 PSU Eagle+Tachometer MC Ag Meister II/FGS + Ortofon SPU MONO CABLES Arm Yannis 420.5 Litz+ SpeakerPC Tripple C+WBT-0681 Ag IC Oyaide FTVS-510 AgWBT 0110Ag Phonostages Paradise(4 Box Mega-Modded) / Croft Musicmaker
Location: Athens
Posts: 268
I'm Dimitris.
Yeah it's hard to beat IKEA if you just want something that works
Sources: Modified SL1200 MK2, Salas folded RIAA, Phonoclone, VSPS, Shelter 501 MK2, Modified Pioneer P6D6 as transport, Shigaclone transport, Peter Daniel NOS DAC.
Amplification: Custom 211 Monoblocks, Electrocompaniet AW120, Audio Research VS110, Gainclone
Loudspeakers: Tannoy Turnberry, PBN Montana EP Signature
Cables/stands: Tempflex ribbon and Twinax cables
Other: Promitheus Signature Passive Attenuator, Custom JFET - transformer preamp.
I'll be messing around with some new spiked feet under the old IKEA chopping board. I'm hoping to get a nice subtle improvement for the small outlay. Stay tuned!
SS
CD Teac VRDS25X(Audiotuned) DECK 1210 Mat Crystal Audio Mods MN Base/Bearing/Platter+Ebony armboard Feet Isonoe PSU Paul Hynes SR7EHD-27XL/DCSXL Ag DC lead/3 Stage Regs/Recap PCB+No Pitch/Strobe/Light ARM SME V(Kondo Ag Rewire&Tags) MC Cadenza Black FGS CABLES Arm Yannis SPD-4 IC Yannis 222 Litz+Ag bullets Power WAR PRE ATC SCA2 SPEAKERS ATC 50ASL STANDS Atacama PHONO Sugden Masterclass PA4 SUT Ortofon ST80SE POWER PSAudio P10
VALVE
PRE Croft Epoch(Modded) AMP Sondex S100 (Modded) SPEAKERS Tannoy 15"MG+RFC Warwick cabs+ Ref XO + Batpure supertweeters DECK Garrard 301 Mat Teunto Bearings 401(Bastin) Plinth Bamboo Arms 3009/3012 PSU Eagle+Tachometer MC Ag Meister II/FGS + Ortofon SPU MONO CABLES Arm Yannis 420.5 Litz+ SpeakerPC Tripple C+WBT-0681 Ag IC Oyaide FTVS-510 AgWBT 0110Ag Phonostages Paradise(4 Box Mega-Modded) / Croft Musicmaker
This is the one I use. A nice solid bit of Bamboo. Works well and definitely changed the sound for the better with spikes.
http://www.argos.co.uk/product/2809467
Technics SL1210 MK2 fully rebuilt and repainted. Ortofon 2M Black Cart, Isonoe isolation feet , MN bearing and Funk Firm platter upgrade, Oyaide RCA Tone Arm and speaker cables, Jelco SA-750D Tonearm. Oyaide HS-TF Carbon headshell, MCRU Linear External PSU, High Fidelity Crystal glass turntable matt, Blue LED upgrade, Denon AVR-2808CI Amp, Bowers and Wilkins DM602S3 Speakers,
Black Rhodium Jazz power cables for amp and turntable, Firebottle mk2 Phono Stage.
SS
CD Teac VRDS25X(Audiotuned) DECK 1210 Mat Crystal Audio Mods MN Base/Bearing/Platter+Ebony armboard Feet Isonoe PSU Paul Hynes SR7EHD-27XL/DCSXL Ag DC lead/3 Stage Regs/Recap PCB+No Pitch/Strobe/Light ARM SME V(Kondo Ag Rewire&Tags) MC Cadenza Black FGS CABLES Arm Yannis SPD-4 IC Yannis 222 Litz+Ag bullets Power WAR PRE ATC SCA2 SPEAKERS ATC 50ASL STANDS Atacama PHONO Sugden Masterclass PA4 SUT Ortofon ST80SE POWER PSAudio P10
VALVE
PRE Croft Epoch(Modded) AMP Sondex S100 (Modded) SPEAKERS Tannoy 15"MG+RFC Warwick cabs+ Ref XO + Batpure supertweeters DECK Garrard 301 Mat Teunto Bearings 401(Bastin) Plinth Bamboo Arms 3009/3012 PSU Eagle+Tachometer MC Ag Meister II/FGS + Ortofon SPU MONO CABLES Arm Yannis 420.5 Litz+ SpeakerPC Tripple C+WBT-0681 Ag IC Oyaide FTVS-510 AgWBT 0110Ag Phonostages Paradise(4 Box Mega-Modded) / Croft Musicmaker
These look nice . Got a link to these feet Andy . I may try them on mine as there's no way of adjusting the GL75 .
Regards
Brian
Sell your cleverness and buy bewilderment . (Rumi )
Korus Computer Audio music server
JustBoom DAC . HRT Musicstreamer 2
Amplifier : Sony TA FB740R
Speakers : Tannoy 637
Interconnects : MS Audio / Klotz MC5000 .
Speaker cables : Western Electric 16AG
Technics SL1210 MK2 fully rebuilt and repainted. Ortofon 2M Black Cart, Isonoe isolation feet , MN bearing and Funk Firm platter upgrade, Oyaide RCA Tone Arm and speaker cables, Jelco SA-750D Tonearm. Oyaide HS-TF Carbon headshell, MCRU Linear External PSU, High Fidelity Crystal glass turntable matt, Blue LED upgrade, Denon AVR-2808CI Amp, Bowers and Wilkins DM602S3 Speakers,
Black Rhodium Jazz power cables for amp and turntable, Firebottle mk2 Phono Stage.
Hi, did you swap over to spiked feet from the Isonoe feet?
SS
CD Teac VRDS25X(Audiotuned) DECK 1210 Mat Crystal Audio Mods MN Base/Bearing/Platter+Ebony armboard Feet Isonoe PSU Paul Hynes SR7EHD-27XL/DCSXL Ag DC lead/3 Stage Regs/Recap PCB+No Pitch/Strobe/Light ARM SME V(Kondo Ag Rewire&Tags) MC Cadenza Black FGS CABLES Arm Yannis SPD-4 IC Yannis 222 Litz+Ag bullets Power WAR PRE ATC SCA2 SPEAKERS ATC 50ASL STANDS Atacama PHONO Sugden Masterclass PA4 SUT Ortofon ST80SE POWER PSAudio P10
VALVE
PRE Croft Epoch(Modded) AMP Sondex S100 (Modded) SPEAKERS Tannoy 15"MG+RFC Warwick cabs+ Ref XO + Batpure supertweeters DECK Garrard 301 Mat Teunto Bearings 401(Bastin) Plinth Bamboo Arms 3009/3012 PSU Eagle+Tachometer MC Ag Meister II/FGS + Ortofon SPU MONO CABLES Arm Yannis 420.5 Litz+ SpeakerPC Tripple C+WBT-0681 Ag IC Oyaide FTVS-510 AgWBT 0110Ag Phonostages Paradise(4 Box Mega-Modded) / Croft Musicmaker