The back was scratched, but they sent a replacement Barry, so all is good.Originally Posted by Barry
Moderator & Terminator!
Location: N E Kent
Posts: 51,768
I'm Geoff.
The back was scratched, but they sent a replacement Barry, so all is good.
It is impossible for anything digital to sound analogue, because it isn't analogue!
Senior Member
Location: West Sūžsēaxe
Posts: 2,012
I'm Edward.
Hope the sale completes ok and the buyer does not muck you around Geoff.
Current: [P20] Roon/Tidal > Custom PC> Chevron Paradox NDF16 > Phast Pre > Neuro. 686 > Tannoy Berkley (RFC tweaks)
Moderator & Terminator!
Location: N E Kent
Posts: 51,768
I'm Geoff.
Fingers crossed. The buyer has good feedback.
It is impossible for anything digital to sound analogue, because it isn't analogue!
Senior Member
Location: Bournemouth
Posts: 5,338
I'm Dan.
What are you replacing the tannoys with?
Pre and Power Amplifiers
Quad 33 Pre with Quad 303 Power Amplifier
Loudspeakers
Quad ESL 57 Loudspeakers
Speaker Cables / Interconnects
Basic Copper Speaker Cable / Cheap Interconnects / -10DB Attenuators
Digital + DAC + PSU
Sony RCD W100 Transport / Beresford Caiman DAC / Paul Hynes SR4 PSU / Chrord Coax for TV / Optical out from Sony
Vinyl Front End
EST4 with SME 3009 S2 Improved with Shure M95ED Cartridge
Cassette
Technics RS D550
Reel to Reel Machines
1967 Ferguson 3218 - MONO
Revox A77 with Teac :S X8 MK Loudspeakers
Moderator & Terminator!
Location: N E Kent
Posts: 51,768
I'm Geoff.
I've also got smaller Tannoys and my little Ruarks and loads of interesting drive units. There might be a horn speaker project soon
It is impossible for anything digital to sound analogue, because it isn't analogue!
Senior Member
Location: Bournemouth
Posts: 5,338
I'm Dan.
Master plan interesting. ☺����I've also got smaller Tannoys and my little Ruarks and loads of interesting drive units. There might be a horn speaker project soon
Pre and Power Amplifiers
Quad 33 Pre with Quad 303 Power Amplifier
Loudspeakers
Quad ESL 57 Loudspeakers
Speaker Cables / Interconnects
Basic Copper Speaker Cable / Cheap Interconnects / -10DB Attenuators
Digital + DAC + PSU
Sony RCD W100 Transport / Beresford Caiman DAC / Paul Hynes SR4 PSU / Chrord Coax for TV / Optical out from Sony
Vinyl Front End
EST4 with SME 3009 S2 Improved with Shure M95ED Cartridge
Cassette
Technics RS D550
Reel to Reel Machines
1967 Ferguson 3218 - MONO
Revox A77 with Teac :S X8 MK Loudspeakers
Moderator & Terminator!
Location: N E Kent
Posts: 51,768
I'm Geoff.
Just bought these KEF Q3 cabinets off ebay for a bit of fun. It'll allow me to test some drivers I have knocking about.
It is impossible for anything digital to sound analogue, because it isn't analogue!
Moderator & Terminator!
Location: N E Kent
Posts: 51,768
I'm Geoff.
Finally got these done. Sounding very decent actually. I seem to have mislaid two driver mounting screws, I'll rummage for replacements.Tonight's project.
A pair of Mission 762 speakers with completely rotted foam cone surrounds. Got some rubber (not foam) surrounds that don't fit due to the originals having a very narrow roll so I've trimmed about 4mm off the cone all round to make them fit. It'll work and I'll have these up and running soon.
Don't care about originality on these as long as they work.
It is impossible for anything digital to sound analogue, because it isn't analogue!
Moderator & Terminator!
Location: N E Kent
Posts: 51,768
I'm Geoff.
Had a box delivered this afternoon.
It is impossible for anything digital to sound analogue, because it isn't analogue!
Senior Member
Location: The Black Country
Posts: 6,273
I'm Alan.
Yah!
When you've checked them out and found out how good they are you may want to slow the fan down to make it quieter.
Wire a 180 ohm resistor in series with the fan. The case splits left and right btw.
Posting Permissions
Reply With Quote