Moode Player Help

[mikeyb]

Here we go....

pi@moode:~ $ cat /var/log/moode.log
20160812 093853 worker: Startup
20160812 093858 worker: Host (moode)
20160812 093858 worker: Hdwr (Pi-1B 512MB)
20160812 093858 worker: Arch (armv6l)
20160812 093858 worker: Krnl (4.4.8+)
20160812 093858 worker: OS (moodeOS 1.0)
20160812 093858 worker: Rel (Moode 2.6 2016-06-07)
20160812 093858 worker: Upd (2016-07-28)
20160812 093858 worker: MPD (0.19.15)
20160812 093858 worker: Session loaded
20160812 093858 worker: Debug logging (off)
20160812 093858 worker: File check...
20160812 093902 worker: File check ok
20160812 093902 worker: Auto-shuffle deactivated
20160812 093903 worker: USB sources (none attached)
20160812 093904 worker: MPD started
20160812 093905 worker: wlan0 does not exist
20160812 093905 worker: UPnP renderer started
20160812 093905 worker: Audio (I2S audio device)
20160812 093905 worker: Audio (IQaudIO Pi-DAC)
20160812 093907 worker: PCM5122 chip options applied
20160812 093911 worker: ALSA outputs unmuted
20160812 093911 worker: ALSA mixer name (Digital)
20160812 093911 worker: MPD volume control (hardware)
20160812 093911 worker: MPD output 1 Output (enabled)
20160812 093911 worker:
20160812 093912 worker: Hdwr volume controller exists
20160812 093912 worker: Volume level (0) restored
20160812 093912 worker: wlan0 address not assigned
20160812 093913 worker: eth0 exists
20160812 093913 worker: eth0 wait 1 for address
20160812 093916 worker: eth0 (192.168.1.227)
20160812 093916 worker: Airplay receiver started
20160812 093918 worker: NAS sources (mountall initiated)
20160812 093918 worker: MPD consume reset to off
20160812 093918 worker: Watchdog started
20160812 093918 worker: End startup
20160812 093918 worker: Ready
pi@moode:~ $


Same again..... Alsamixer settings within configure back to zero.

[TimCurtis]

Here we go....

pi@moode:~ $ cat /var/log/moode.log
20160812 093853 worker: Startup
20160812 093858 worker: Host (moode)
20160812 093858 worker: Hdwr (Pi-1B 512MB)
20160812 093858 worker: Arch (armv6l)
20160812 093858 worker: Krnl (4.4.8+)
20160812 093858 worker: OS (moodeOS 1.0)
20160812 093858 worker: Rel (Moode 2.6 2016-06-07)
20160812 093858 worker: Upd (2016-07-28)
20160812 093858 worker: MPD (0.19.15)
20160812 093858 worker: Session loaded
20160812 093858 worker: Debug logging (off)
20160812 093858 worker: File check...
20160812 093902 worker: File check ok
20160812 093902 worker: Auto-shuffle deactivated
20160812 093903 worker: USB sources (none attached)
20160812 093904 worker: MPD started
20160812 093905 worker: wlan0 does not exist
20160812 093905 worker: UPnP renderer started
20160812 093905 worker: Audio (I2S audio device)
20160812 093905 worker: Audio (IQaudIO Pi-DAC)
20160812 093907 worker: PCM5122 chip options applied
20160812 093911 worker: ALSA outputs unmuted
20160812 093911 worker: ALSA mixer name (Digital)
20160812 093911 worker: MPD volume control (hardware)
20160812 093911 worker: MPD output 1 Output (enabled)
20160812 093911 worker:
20160812 093912 worker: Hdwr volume controller exists
20160812 093912 worker: Volume level (0) restored
20160812 093912 worker: wlan0 address not assigned
20160812 093913 worker: eth0 exists
20160812 093913 worker: eth0 wait 1 for address
20160812 093916 worker: eth0 (192.168.1.227)
20160812 093916 worker: Airplay receiver started
20160812 093918 worker: NAS sources (mountall initiated)
20160812 093918 worker: MPD consume reset to off
20160812 093918 worker: Watchdog started
20160812 093918 worker: End startup
20160812 093918 worker: Ready
pi@moode:~ $


Same again..... Alsamixer settings within configure back to zero.

Hi Mike,

The log entries below indicate an issue with the MPD/Crossfeed config, probably due to the post-update steps for 2016-07-28 update not having been completed. If you complete the steps it should fix the volume issue.

Indicates bad config

20160812 093911 worker: MPD output 1 Output (enabled)
20160812 093911 worker:

Indicates correct config

20160801 212322 worker: MPD output 1 ALSA default (enabled)
20160801 212322 worker: MPD output 2 ALSA crossfeed (disabled)

2016-07-28 update instructions

This package can take several minutes to complete due to components that are downloaded and installed from Jessie repo.

After reboot APPLY MPD config then toggle Crossfeed setting on System config to establish Crossfeed/MPD outputs. Verify by "mpc outputs" which should show ALSA default enabled and ALSA crossfeed disabled.

Remember to BACKUP Moode SD Card before updating.

-Tim

[r100]

(couldn't find the pop-corn icon)

[TimCurtis]

Hi, here are a few pics of IQaudIO Pi-DigiAMP+ and DAC+ wired into Moode Cases :-)

-Tim

[Acousticmood]

I want to connect to my car using the accesss point feature to drive my pi and hifiberry pro plus. The high fi berry doesn't have a headphone out so I tried a stereo to headphone cord in reverse (usually I use this cord to connect the headphone out in my phone to a stereo in on my amplifier). It doesn't work well at all with no stereo separation and intense buzzing.

Shouldn't this work in reverse? Anyone have any ideas? Thanks

[Acousticmood]

I want to connect to my car using the accesss point feature to drive my pi and hifiberry pro plus. The high fi berry doesn't have a headphone out so I tried a stereo to headphone cord in reverse (usually I use this cord to connect the headphone out in my phone to a stereo in on my amplifier). It doesn't work well at all with no stereo separation and intense buzzing.

Shouldn't this work in reverse? Anyone have any ideas? Thanks

Well problem solved - it was a ground loop. I put an isolator in and it went away.

[TimCurtis]

Hi,

Moode 2.6 2016-08-28 update available.

READ CAREFULLY

Installing this update package followed by manually updating the kernel to 4.4.19 via the rpi-update command below will effectivly upgrade Moode 2.6 to Moode 2.7. If the updated kernel is not installed then NO SUPPORT will be provided!

sudo rpi-update 818a860cf690d64c62d3227ad9c36d5867a671c2
sudo reboot
sudo rm -rf /boot.bak
sudo rm -rf /lib/modules.bak
sudo rm -rf /lib/modules/4.4.8+
sudo rm -rf /lib/modules/4.4.8-v7+

The update package can take several minutes to complete due to components that are downloaded and installed from Jessie repo. After pressing INSTALL, if the message "Software update complete, Reboot required" appears immediately, just ignore it and wait several minutes. There is bug in Worker that prevents System config screen from auto-waiting before displaying the completion message. The bug is fixed in this update.

The update process can be monitored by ssh TOP to determine when its ok to reboot. Look for apt-get and mandb running. When they are both finished and no longer appear in list, its safe to reboot.

1) One of the updates installs HTML files that revert the knob colors to Emerald. Use Customize to set another color, then back to your favorite color, then refresh.

2) The wonderful Crossfeed DSP plugin is included in this update and there is a config change to enable Airplay over AP mode. IMPORTANT: To establish Crossfeed/MPD outputs and Airplay over AP mode its necessary to perform the steps below after reboot.

a) MPD config, APPLY
b) System config, set Crossfeed DSP to 725 Hz 4.5 dB then set it back to disabled.
c) The config can be verified by running the cmd below from ssh session

pi@moode:~ $ mpc outputs
Output 1 (ALSA default) is enabled
Output 2 (ALSA crossfeed) is disabled
pi@moode:~ $

d) Network config, APPLY
e) This will update the configuration for Airplay over AP mode

3) Several configuration changes are included that provide improved support for loading large collections into the Library panel.

4) New commercial-free, listener-supported radio stations and support for exciting new I2S audio devices are included in this update, and a new universal rotary encoder driver that updates Moode volume knob and supports both hardware and software volume.

Finally, it's always a good idea to BACKUP the SD Card before installing updates :-)

Enjoy!

Regards,
Tim

Package contents

-- New Features

NEW: In-place software updater
NEW: Crossfeed DSP for headphone listening
NEW: Support Meridian Explorer 2 and MQA
NEW: Cache PHP session data using memcache
NEW: Restart.sh script for reboot/poweroff
NEW: Setting to turn off Pi-3 WiFi/BT adapter
NEW: Sys config settings for kbd and layout
NEW: Universal rotary encoder driver

-- Media

NEW: AddictedToRadio - Quiet Storm
NEW: Buddah Radio
NEW: Positivly Baroque
NEW: Radio FM4
NEW: Audiophile Lounge
NEW: Audiophile Rock-Blues
UPD: Zen FM stream link to mp3
UPD: Audiophile Baroque stream link
UPD: Audiophile Classical stream link
UPD: Audiophile Jazz stream link
UPD: The Jazz Groove stream link

-- Audio devices (i2s)

NEW: Dion Audio LOCO
NEW: IQaudIO Digi+
NEW: JustBoom DAC HAT(Zero)
NEW: JustBoom AMP HAT(Zero)
NEW: JustBoom Digi HAT(Zero)
NEW: Mamboberry LS DAC+
NEW: Red Rocks Audio DigiDAC1

-- Updates

UPD: Bump to MPD version 0.19.19
UPD: Bump to Linux kernel 4.4.19 (manually via rpi-update)
UPD: Improved watchdog monitoring
UPD: Change MPD socket connection to use debugLog()
UPD: Clean up wording on Net config and Restart screens
UPD: Add 32/176.4, 32/352.8 sample rates to SoX list
UPD: Bump NGINX fastcgi_read_timeout
UPD: Use UNIX socket for PHP/NGINX interprocess comms
UPD: Add update package date to Moode log and About
UPD: Clean up wording on MPD config screen
UPD: Add capability to install test updates
UPD: Add MPD outputs to Moode startup log
UPD: Add "no setup" to resp check in parseHwParams
UPD: Breakout airplay volume array for debug log
UPD: Bump PHP FPM max_execution_time to 180 secs
UPD: Get ALSA mixer name dynamically
UPD: Add vol.php to command/index.php
UPD: Add hover help to coverart links
UPD: Bump wait time for eth0 check during startup
UPD: Add mpd state to currentsong.txt
UPD: Add ext3 file system to udisks-glue config
UPD: Leave volume knob enabled when rotary encoder
UPD: Clean up some syntax
UPD: Add Generic-1 I2S (hifiberry-dac)
UPD: Add Generic-2 I2S (rpi-dac)
UPD: Contribs

-- Bug fixes

FIX: Remove circular symlinks in /mnt for NAS and SDCARD
FIX: Playback panel toolbar not visible on iPad Mini
FIX: DHCP addr being assigned when eth0 set to static addr
FIX: Fail to get cover art embedded in AIFF format
FIX: Wrong encodedAT rate displayed for UPnP files
FIX: Wrong indextpl.html cp file in 2016-07-10 update
FIX: Audioinfo volume "disabled" not being displayed
FIX: ALSA mixer names with embedded spaces not parsed
FIX: Airplay not working over AP mode

[TimCurtis]

Hi,

Moode Audio Player release 2.7 is available for download at moodeaudio.org :-)

This release includes a new in-place software updater, Crossfeed DSP for headphone listening, support for Meridian Explorer 2 and MQA format, a universal rotary encoder driver that updates Moode volume knob and supports both hardware and software volume, some really great commercial-free, listener-supported radio stations, support for exciting new I2S audio devices, and numerous important updates and bug fixes.

Please read the attached Release Notes and view the Setup Guide at moodeaudio.org for more information.

Enjoy!

Regards,
Tim Curtis

======================
2.7 Release 2016-08-28
======================

New features

- NEW: In-place software updater
- NEW: Crossfeed DSP for headphone listening
- NEW: Support Meridian Explorer 2 and MQA
- NEW: Cache PHP session data using memcache
- NEW: Restart.sh script for reboot/poweroff
- NEW: Setting to turn off Pi-3 WiFi/BT adapter
- NEW: Sys config settings for kbd and layout
- NEW: Universal rotary encoder driver

Media

- NEW: AddictedToRadio - Quiet Storm
- NEW: Buddah Radio
- NEW: Positivly Baroque
- NEW: Radio FM4
- NEW: Audiophile Lounge
- NEW: Audiophile Rock-Blues
- UPD: Zen FM stream link to mp3
- UPD: Audiophile Baroque stream link
- UPD: Audiophile Classical stream link
- UPD: Audiophile Jazz stream link
- UPD: The Jazz Groove stream link

Audio devices (i2s)

- NEW: Dion Audio LOCO
- NEW: IQaudIO Digi+
- NEW: JustBoom DAC HAT(Zero)
- NEW: JustBoom AMP HAT(Zero)
- NEW: JustBoom Digi HAT(Zero)
- NEW: Mamboberry LS DAC+
- NEW: Red Rocks Audio DigiDAC1

Updates

- UPD: Bump to MPD version 0.19.19
- UPD: Bump to Linux kernel 4.4.19
- UPD: Improved watchdog monitoring
- UPD: Change MPD socket connection to use debugLog()
- UPD: Clean up wording on Net config and Restart screens
- UPD: Add 32/176.4, 32/352.8 sample rates to SoX list
- UPD: Bump NGINX fastcgi_read_timeout
- UPD: Use UNIX socket for PHP/NGINX interprocess comms
- UPD: Add update package date to Moode log and About
- UPD: Clean up wording on MPD config screen
- UPD: Add capability to install test updates
- UPD: Add MPD outputs to Moode startup log
- UPD: Add "no setup" to resp check in parseHwParams
- UPD: Breakout airplay volume array for debug log
- UPD: Bump PHP FPM max_execution_time to 180 secs
- UPD: Get ALSA mixer name dynamically
- UPD: Add vol.php to command/index.php
- UPD: Add hover help to coverart links
- UPD: Bump wait time for eth0 check during startup
- UPD: Add mpd state to currentsong.txt
- UPD: Add ext3 file system to udisks-glue config
- UPD: Leave volume knob enabled when rotary encoder
- UPD: Clean up some syntax
- UPD: Add Generic-1 I2S (hifiberry-dac)
- UPD: Add Generic-2 I2S (rpi-dac)
- UPD: Contribs

Bug fixes

- FIX: Remove circular symlinks for SDCARD and NAS
- FIX: Playback panel toolbar not visible on iPad Mini
- FIX: DHCP addr being assigned when eth0 set to static addr
- FIX: Fail to get cover art embedded in AIFF format
- FIX: Wrong encodedAT rate displayed for UPnP files
- FIX: Null printed in Moode log for USB sources
- FIX: Wrong indextpl.html cp file in 2016-07-10 update
- FIX: Audioinfo volume "disabled" not being displayed
- FIX: ALSA mixer names with embedded spaces not parsed
- FIX: Airplay not working over AP mode

[Bonky]

For anyone trying to get the Audiphonics Sabre DAC to work with the screen and power management, please see this:

Bonjour,

When have you bought the I-Sabre V3 (we just changed the regulator).
We've just put online dedicated modded software to use the screen and power management on various audio releases.

you can find it here :

Nous rassemblons ici les différentes versions et évolutions des solutions softwares modifiées dédiées aux RaspDac :
"Here you can find all the modded audio releases dedicated to Raspdac product range" :


MoodeAudio

--"MoodeAudio" avec gestion de l'alimentation (I-Sabre V3 et Audiophonics PI-SPC) :
With power management :

https://mega.nz/#!8AwHECpT!PHMOpwo7s...fxNLDPikfDU2Dk

--"MoodeAudio" avec gestion de l'alimentation (I-Sabre V3 et Audiophonics PI-SPC) et afficheur Oled (Winstar Ecran Oled 16x2) :
With power management and Oled display support :

https://mega.nz/#!kYwWBAxS!35kR-cV3d...EPMRGI_dYUUx0A

Nous compléterons cette liste au fur et a mesure de nos avancées.

Bonne écoute !

[struth]

MoOde 2.7 up and running here. Painless and working fine... Thanks Tim