+ Reply to Thread
Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: 300B Valves run in

  1. #1
    Join Date: Jul 2008

    Location: Devon

    Posts: 75
    I'm Terry.

    Default 300B Valves run in

    Hi Everyone

    Can you help me out with this one? I have just fitted a new matched quad of Golden Lion 300B valves, and on reading a few articles it suggests that they will sound much better after about a hundred or so hours of listening, with this in mind is it ok to run them for 4 days continously, also can I turn the volume down to zero whilst this is being done?
    Many Thanks.

  2. #2
    Join Date: Dec 2017

    Location: Lincolnshire

    Posts: 226
    I'm Martin.

    Default

    Don’t know but personally I’d just use it as normal and see how you go.

  3. #3
    Join Date: Nov 2010

    Location: Yorkshire

    Posts: 8,003
    I'm AnDreW.

    Default

    Your volume wont have any impact. You could disconnect your speakers and have the volume on full tilt if you like !
    SS

    CD Teac VRDS25X(Audiotuned) DAC Caiman SEG+15V PSU+Dorado DECK 1210 Mat SPH SSS Mods MN Base/Bearing/Platter+Ebony armboard Feet Isonoe/Ebony PSU Paul Hynes SR7EHD-27XL/DCSXL Ag DC lead/3 Stage Regs/Recap PCB+No Pitch/Strobe/Light ARM SME V(Kondo Ag Rewire&Tags) MC Cadenza Black CABLES Arm Yannis SPD-4 IC Yannis 222 Litz+Ag bullets Power WAR PRE ATC SCA2 SPEAKERS ATC 50ASL STANDS Atacama PHONO Sugden Masterclass PA4 SUT Ortofon ST80SE POWER PSAudio P10

    VALVE

    PRE
    Croft Epoch(Modified) AMP Sondex S100 (Modified) SPEAKERS Tannoy 15"MG+RFC Warwick cabs+ Reference XO DECKS Garrard301/401 (Bastin) Mat Teunto Bearings 401/SPH Plinth Moldovan/Bastin Arms 3009/3012(Ikeda Ag wired) SME V 12 PSU Eagle+Tachometer MC Ag Meister v2 / Royall N SPU's CABLES Arm Yannis 420.5 Litz+ Speaker 10mm Cu + WBT-0681 Ag IC Oyaide FTVS-510 AgWBT 0110Ag Phonostage Paradise(4 Box Modded) / EAR 834 Clone (modded)

    REAL SOUND


    PRE Radford SC25 (Mullard ECC83/82) POWER RADFORD STA25 Renaissance (Electroharmonix EL34) SPEAKERS Celestion Ditton 15 (Duelund Rewired/Jantzen Recapped) CABLES Speaker - Duelund AWG 12IC - Belden 8402+Switchcraft RCA



  4. #4
    Join Date: Apr 2012

    Location: London

    Posts: 614
    I'm James.

    Default

    Do not do this if its a SET/PSE amp! Even if it is not it is just poor practice and at best will stress several expensive components. I know Rexton was having a laugh but some coming across the thread might take the advice seriously.
    I personally would do as the earlier poster suggested and use it as you normally would. Warming and cooling are also part of the running in process.

    Sent from my BLA-L09 using Tapatalk

  5. #5
    Join Date: Feb 2010

    Posts: 4,173
    I'm Tom.

    Default

    Yes I was just about to jump in there James. Valve amps with transformers in (which is nearly all of them barring a few OTLs) need a load when switched on (ie, connected to speakers). Pentode amps for sure, but I personally wouldn't risk it with a triode amp even if supposedly running with no global feedback.

  6. #6
    Join Date: Jun 2018

    Location: Mildenhall, Suffolk

    Posts: 383
    I'm John.

    Default

    Shouldn't be any rush to run the tubes in, just increase your listening sessions and enjoy the development of the Sweet Spot.

  7. #7
    Join Date: Nov 2008

    Location: belgrade serbia

    Posts: 759
    I'm gordan.

    Default

    Single ended tube amps too are not advised to switch on unloaded.
    Gordan.
    Speakers: Oris Swing MkII
    Amps: Thomas Mayer 300b/ Hiraga La Maison de L'Audiophile 20
    Preamp: Silver AVC by eng. Ferenc Lazar
    Phono Preamp: Shishido LCR by Solaja Audio
    Deck: Garrard 301 Martin Bastin reworked/plinthed with Fidelity Research FR64fx
    Cartridges: SPU Spirit/ Koetsu Black revisited by eng. Salai/ Miyajima Shilabe
    Step Up Transformers: Tango MCT 999/ Ortofon T-5000/ Lumiere SUT
    Digital: Shigaclone by eng. Ferenc Lazar with Lampizator Amber II
    Wires: of sufficient length

  8. #8
    Join Date: Dec 2017

    Location: Lincolnshire

    Posts: 226
    I'm Martin.

    Default

    Just to add I wouldn’t leave a valve amp on and unattended for an extended period anyway.....

  9. #9
    Join Date: Oct 2008

    Location: Glasgowshire

    Posts: 7,577
    I'm availableforweddingsAndBarmitzvas.

    Default

    Been using a 300B SET power amp for a few years now, had 4 sets of 300Bs on it, so familiar with the running in thing.
    Had a set of the Good Lions, nice 300B’s.

    My takeaway?
    Just use as normal and a enjoy the journey.

    Switch on in the morning and keep on till your finished listening at the end of the day.
    No need to switch off and on every hour, think of the valves as lightbulbs!
    Importantly, leave space in your head to enjoy the wonderful sound and enjoy the improvement as it comes along, don’t stress about how it’s gonna sound in 3 months.

    Some points though, some touched upon already:
    - Switching on and off frequently...never a good idea, especially if your amp doesn’t have a ‘soft start’ (no inrush) circuit.
    - Don’t move your amp when it’s hot...ever.
    - With a Triode amp it’s less of an issue, but I’d not take the chance disconnecting speaker cable with the amp on, keep a load on.

    main thing, enjoy your system now and not be thinking about Months down the line!
    I enjoy Hifi n stuff...

  10. #10
    Join Date: Jul 2008

    Location: Devon

    Posts: 75
    I'm Terry.

    Default

    Thank You, Thank You, and Thank You everyone, some great advice there which i will now take on board. So i will be just taking my time and enjoying it along the way. I must admit I can REALLY notice the difference between these new Gold Lion valves and my old ones which I had tested and all four were on their last legs. Merry Crimbo to one and all !!!!

+ Reply to Thread
Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •