+ Reply to Thread
Page 2 of 5 FirstFirst 1234 ... LastLast
Results 11 to 20 of 41

Thread: Resurrecting an old chum

  1. #11
    Join Date: Dec 2014

    Location: UK, inactive

    Posts: 1,570
    I'm inactive.

    Default

    ... and some more goodies from Mr Postman:




    Now the long wait for Chinapost and the vagaries of UK import processes ...... could be gone a while

  2. #12
    Join Date: Nov 2010

    Location: Yorkshire

    Posts: 9,302
    I'm Andrew.

    Default

    SS
    CD Teac VRDS25X(Audiotuned) DECK 1210 Mat Crystal Audio Mods MN Base/Bearing/Platter+Ebony armboard Feet Isonoe PSU Paul Hynes SR7EHD-27XL/DCSXL Ag DC lead/3 Stage Regs/Recap PCB+No Pitch/Strobe/Light ARM SME V(Kondo Ag Rewire&Tags) MC Cadenza Black FGS CABLES Arm Yannis SPD-4 IC Yannis 222 Litz+Ag bullets Power WAR PRE ATC SCA2 SPEAKERS ATC 50ASL STANDS Atacama PHONO Sugden Masterclass PA4 SUT Ortofon ST80SE POWER PSAudio P10

    VALVE
    PRE
    Croft Epoch(Modded) AMP Sondex S100 (Modded) SPEAKERS Tannoy 15"MG+RFC Warwick cabs+ Ref XO + Batpure supertweeters DECK Garrard 301 Mat Teunto Bearings 401(Bastin) Plinth Bamboo Arms 3009/3012 PSU Eagle+Tachometer MC Ag Meister II/FGS + Ortofon SPU MONO CABLES Arm Yannis 420.5 Litz+ SpeakerPC Tripple C+WBT-0681 Ag IC Oyaide FTVS-510 AgWBT 0110Ag Phonostages Paradise(4 Box Mega-Modded) / Croft Musicmaker



  3. #13
    Join Date: Dec 2014

    Location: UK, inactive

    Posts: 1,570
    I'm inactive.

    Default

    eBay tracking says the case arrived in UK on Sept 27 - expected delivery date Oct 15

    ... as if

  4. #14
    Join Date: Nov 2010

    Location: Yorkshire

    Posts: 9,302
    I'm Andrew.

    Default

    Quote Originally Posted by mikmas View Post
    eBay tracking says the case arrived in UK on Sept 27 - expected delivery date Oct 15

    ... as if
    Yeah that's nothing new, welcome to the wonderful world of the UK customs service.
    SS
    CD Teac VRDS25X(Audiotuned) DECK 1210 Mat Crystal Audio Mods MN Base/Bearing/Platter+Ebony armboard Feet Isonoe PSU Paul Hynes SR7EHD-27XL/DCSXL Ag DC lead/3 Stage Regs/Recap PCB+No Pitch/Strobe/Light ARM SME V(Kondo Ag Rewire&Tags) MC Cadenza Black FGS CABLES Arm Yannis SPD-4 IC Yannis 222 Litz+Ag bullets Power WAR PRE ATC SCA2 SPEAKERS ATC 50ASL STANDS Atacama PHONO Sugden Masterclass PA4 SUT Ortofon ST80SE POWER PSAudio P10

    VALVE
    PRE
    Croft Epoch(Modded) AMP Sondex S100 (Modded) SPEAKERS Tannoy 15"MG+RFC Warwick cabs+ Ref XO + Batpure supertweeters DECK Garrard 301 Mat Teunto Bearings 401(Bastin) Plinth Bamboo Arms 3009/3012 PSU Eagle+Tachometer MC Ag Meister II/FGS + Ortofon SPU MONO CABLES Arm Yannis 420.5 Litz+ SpeakerPC Tripple C+WBT-0681 Ag IC Oyaide FTVS-510 AgWBT 0110Ag Phonostages Paradise(4 Box Mega-Modded) / Croft Musicmaker



  5. #15
    Join Date: Dec 2014

    Location: UK, inactive

    Posts: 1,570
    I'm inactive.

    Default

    Quote Originally Posted by mikmas View Post
    eBay tracking says the case arrived in UK on Sept 27 - expected delivery date Oct 15

    ... as if
    Looks like my scepticism was vindicated ... man with the red van rang the door bell this morning, two weeks ahead of given date



    All bits present and correct - and enough little screws in the bag for four more boxes

    Unfortunately, busy til Monday so will have to curb my enthusiasm for now .... unless not .......

  6. #16
    Join Date: Dec 2014

    Location: UK, inactive

    Posts: 1,570
    I'm inactive.

    Default

    Found an old slide from circa 1980 showing the amp in situ ... being fed by a (cosmetically modified) Uher preamp:




    ... the only Chinese import I had at that time being the little drumming panda - 'from little acorns' etc
    Last edited by mikmas; 02-10-2019 at 23:06.

  7. #17
    Join Date: Dec 2014

    Location: UK, inactive

    Posts: 1,570
    I'm inactive.

    Default

    Decided to start with the most tedious bit first and marked out the holes for the amp modules ... hate this kind of job
    Hopefully will find some time over the weekend to cut them out and drill the other holes required.


  8. #18
    Join Date: Dec 2014

    Location: UK, inactive

    Posts: 1,570
    I'm inactive.

    Default

    So found time yesterday to cut the amp holes and a new front panel as well as drill all the necessary:



    followed by a 'dry run' assembly:



    ... after that - some serious snagging

    (TO BE CONTINUED...)

  9. #19
    Join Date: Dec 2014

    Location: UK, inactive

    Posts: 1,570
    I'm inactive.

    Default

    Today was pretty much job done bar a couple of not very important decisions (pot or no pot, silver or black faceplate...etc...)
    Tested out for an hour or so in the garage with various speakers and, other than sorting an initial earthing issue, all went swimmingly

    The main problems I encountered during the re-casing exercise related to the rating of the toroid (220v or 240v?) and some concerns with the mounting bolt.

    I had measured the clearance of the toroid in the old housing and ordered the new case accordingly (knowing that it might be on the tight side height-wise).
    Hadn't reckoned on the case being just a wee bit smaller than advertised (to be fair they had put a size deviation disclaimer on the bay listing .... 'between 1 and 3 cm' )
    When I fitted the toroid initially on the dry run it was immediately apparent that it was just a smidgin too high and was flexing the top lid when I screwed it down.

    As the top and bottom of the case are simply screwed onto flanges in the side panels, I sorted this by adding strips of 2mm plastic at either side and top and bottom - creating an additional 4mm breathing space at the top thus:



    The eagle-eyed amongst you will probably notice the electrical tape liberally applied to the toroid mounting washer - just a cure for a bit of possibly unnecessary paranoia caused by too much reading on t'interweb

  10. #20
    Join Date: Dec 2014

    Location: UK, inactive

    Posts: 1,570
    I'm inactive.

    Default

    I mentioned already that I had some niggles about the exact spec of the toroid that I sourced from ILP (at the same time I bought the HY60 amp modules and rectifier board).
    I have the original spec sheets for the HY60 amp module and these mention two appropriate toroids for the set up - one for 120/240v and one for 220v.
    As I was living in Holland at the time I suspected that the one I had was probably the 220v version - however the model number on mine didn't match either of those on the spec sheet

    After some searching around various suppliers websites, I came across a UK based transformer manufacturer who apparently used to make toroids for ILP so I contacted him - got a quick reply but he couldn't help me out with that model number (although he did suggest an appropriate alternative..)

    Further searching got me the email address (tucked away on eBay) of the current owner of ILP who still sells the amp modules (although his main business now appears to be stair-rod related ...)
    https://www.ebay.co.uk/str/ILP-Direc...p2047675.l2563

    He confirmed that the model number I had given indicated a 240v primary ... phew ...

    Unfortunately while scrabbling around toroid specs and data sheets in search of info and knowledge I came across some scarier stuff .....

    (TO BE CONTINUED ....)

+ Reply to Thread
Page 2 of 5 FirstFirst 1234 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •