My post was not directed at you Barry.Originally Posted by Barry
Senior Member
Location: Grimsby
Posts: 398
I'm David.
My post was not directed at you Barry.
Fount Master & Moderator
Location: Essex
Posts: 31,984
I'm openingabottleofwine.
No worries David.
Barry
Senior Member
Location: Solihull
Posts: 716
I'm Martin.
Gentlemen......................
To bring some sanity back to this thread.
I am a new Voyd Valdi owner and I I am having trouble in setting up the TT
I have an Audio Note Arm 1 V2 to install and so far have been unsuccessful and am in need of help.
I am in Solihull and would welcome help from anybody reasonably close or perhaps a knowledgeable dealer
Lumley Heliosphere Audiomods 5
Voyd Valdi AN Arm 1 V2 and Denon MC
Audiomeca Talisman Highly Modded
Audiomeca Kreatura &,SW1X DAC1
Hovland HP200 MC
Hovland Radia
Ming Da 805 monos
Magnum Dynalab Etude, RWA Cassabria + LCD 3
Wilson Benesch Actors
Cables by Cardas, Hovland G3 and Yter
Senior Member
Location: Seaton, Devon, UK
Posts: 13,261
I'm Adrian.
Hi can you describe the problem you are having? May be able to advise.
Sent from my iPhone using Tapatalk
Listening is the act of aural discrimination and dissemination of sound, and accepting you get it wrong sometimes.
Analog Inputs: Pro-Ject Signature 10 TT & arm, Benz Micro LP-S, Michel Cusis MC, Goldring 2500 and Ortofon Rondo Blue cartridges, Hitachi FT5500 mk2 Tuner
Digital:- Marantz SA-KI Pearl CD player, RaspberryPi/HifiBerry Digi+ Pro, Buffalo NAS Drive
Amplification:- AudioValve Sunilda phono stage, Krell KSP-7B pre-amp, Krell KSA-80 power amp
Output: Wilson Benesch Vector speakers, KLH Ultimate One Headphones
Cables: Tellurium Q Ultra Black II RCA & Chord Epic 2 RCA, various speaker leads, & links
I think I am nearing audio nirvana, but don’t tell anyone.
Senior Member
Location: Banbury, Oxfordshire/Panteg is where my late father was born
Posts: 4,382
I'm Chris.
Is it the armboard? I think that Simon of SJS can help if you need an armboard.
Chris
We've gone on holiday by mistake !
Senior Member
Location: Solihull
Posts: 716
I'm Martin.
SJS Simon has made me a suitable armboard...so thats OK
Having trouble adjusting the suspension and bringig the platter down to 5mm off the topplate. Just how far can the inserts protrude?
Also the AN arm cable seems to be remarkably inflexible and I cannot see how to dress the cable using the P clip. Doing it that way would foul the suspension pillar and motor.
At some point I may have to drill the plinth to exit the cable but until I find how best to dress the cable I cannot determine where to drill
Lumley Heliosphere Audiomods 5
Voyd Valdi AN Arm 1 V2 and Denon MC
Audiomeca Talisman Highly Modded
Audiomeca Kreatura &,SW1X DAC1
Hovland HP200 MC
Hovland Radia
Ming Da 805 monos
Magnum Dynalab Etude, RWA Cassabria + LCD 3
Wilson Benesch Actors
Cables by Cardas, Hovland G3 and Yter
Senior Member
Location: Banbury, Oxfordshire/Panteg is where my late father was born
Posts: 4,382
I'm Chris.
Have you tried looping the cable, then into the p-clip.
Chris
We've gone on holiday by mistake !
Trade: SJS Electroacoustics
Location: Manchester, UK
Posts: 266
I'm Simon.
the trick is always to loop the arm cable before the P clip so it can move vertically with freedom, but also doesn't drag the sub-chassis around horizontally. easier said than done
Here is a photo of my AN Arm 1-3 mk2 with the arm cable dressed inside the Voyd and exiting through the regular hole in the chassis. hopefully it helps to illustrate things.
It should not be necessary to drill new holes in the frame.
SJS Arcadia Line Level Pre-amplifiers, Headphone amps, MM Phono Stages and SET Power amps - service, repairs, upgrades.
Designed and hand-built in England.
Senior Member
Location: Banbury, Oxfordshire/Panteg is where my late father was born
Posts: 4,382
I'm Chris.
That is how I set mine up Simon.
Chris
We've gone on holiday by mistake !
Senior Member
Location: Solihull
Posts: 716
I'm Martin.
Aha! now it makes more sense. My Valdi strangely does not have an armcable exit at all!!the trick is always to loop the arm cable before the P clip so it can move vertically with freedom, but also doesn't drag the sub-chassis around horizontally. easier said than done
Here is a photo of my AN Arm 1-3 mk2 with the arm cable dressed inside the Voyd and exiting through the regular hole in the chassis. hopefully it helps to illustrate things.
It should not be necessary to drill new holes in the frame.
Can't imagine how that was intended
I will have to search out a suitable drill now I have a good idea where the exit hole should be
Thanks Simon for the picture.
Doubtless be in touch when it comes to putting the belt on !!!!!!!!!!!!!
Lumley Heliosphere Audiomods 5
Voyd Valdi AN Arm 1 V2 and Denon MC
Audiomeca Talisman Highly Modded
Audiomeca Kreatura &,SW1X DAC1
Hovland HP200 MC
Hovland Radia
Ming Da 805 monos
Magnum Dynalab Etude, RWA Cassabria + LCD 3
Wilson Benesch Actors
Cables by Cardas, Hovland G3 and Yter
Posting Permissions
Reply With Quote
