+ Reply to Thread
Results 1 to 10 of 10

Thread: wanted patch cable for michell orbe , to extend the power supply to the motor ,,

  1. #1
    Join Date: May 2016

    Location: wales

    Posts: 450
    I'm peter.

    Default wanted patch cable for michell orbe , to extend the power supply to the motor ,,

    hi i am looking for a patch /extension cable for the michell orbe controler to the motor , the std one is too short ,, it needs to have a 6 pin din male and female,
    regards
    peter

  2. #2
    Join Date: Nov 2011

    Location: Seaton, Devon, UK

    Posts: 1,856
    I'm Adrian.

    Default

    [FONT="Arial"]
    Listening is the act of aural discrimination and dissemination of sound


    Voyd the Voyd (slightly modified), SME IV arm(special build virtually a V) and JELCO TK850M(10"), Benz Micro LP-S & Michel Cusis MC cartridge, Furutech AG-12-R4 High Performance Phono Cable, LFD MMC special phono stage, RaspberryPi/HifiBerry Digi to Beresford Caiman SEG DAC, Meridian 508 CD to Caiman SEG, ALLNIC T1500 MKII SET 300B amp, Vienna Acoustics Mozart SE speakers and JBL L100 Century's , Chord Epic speaker leads, & signature links, the Eccose Conductor CA1 cd to pre

  3. #3
    Join Date: May 2016

    Location: wales

    Posts: 450
    I'm peter.

    Default

    no it will not fit as it has to have the locking type,, https://www.ebay.co.uk/itm/GX12-GX16...mkt-0ng7eZL-BA

    13mm diameter which is the problem

    but thanks for looking

  4. #4
    Join Date: Mar 2009

    Location: Nottingham

    Posts: 248
    I'm Ian.

    Default

    When I had to extend my gyro psu cable I took the plug to the deck off the lead, replaced it with a 240v inline power connector then added some more cable and put the plug back on the end of that. All screw terminals' so easily reversible with my psu

  5. #5
    Join Date: May 2016

    Location: wales

    Posts: 450
    I'm peter.

    Default

    the orbe uses a 6 pin Din , it needs to be male and female connection, , not 240 v , cheers pete

  6. #6
    Join Date: Nov 2011

    Location: Seaton, Devon, UK

    Posts: 1,856
    I'm Adrian.

    Default

    Quote Originally Posted by gwernaffield View Post
    no it will not fit as it has to have the locking type,, https://www.ebay.co.uk/itm/GX12-GX16...mkt-0ng7eZL-BA

    13mm diameter which is the problem

    .

    but thanks for looking
    Splice and dice then with 6 part lead
    [FONT="Arial"]
    Listening is the act of aural discrimination and dissemination of sound


    Voyd the Voyd (slightly modified), SME IV arm(special build virtually a V) and JELCO TK850M(10"), Benz Micro LP-S & Michel Cusis MC cartridge, Furutech AG-12-R4 High Performance Phono Cable, LFD MMC special phono stage, RaspberryPi/HifiBerry Digi to Beresford Caiman SEG DAC, Meridian 508 CD to Caiman SEG, ALLNIC T1500 MKII SET 300B amp, Vienna Acoustics Mozart SE speakers and JBL L100 Century's , Chord Epic speaker leads, & signature links, the Eccose Conductor CA1 cd to pre

  7. #7
    Join Date: May 2016

    Location: wales

    Posts: 450
    I'm peter.

    Default

    i would but it is not mine,, also look a mess, pete

  8. #8
    Join Date: Nov 2011

    Location: Seaton, Devon, UK

    Posts: 1,856
    I'm Adrian.

    Default

    Quote Originally Posted by gwernaffield View Post
    i would but it is not mine,, also look a mess, pete
    I wasnt suggesting you did it the dirty way with insulation tape. If you buy 2 male and 2 female 6 pins and the lead needed then you can solder each up and have the extension in place. Alternatively if the existing socket will come apart and not heat sealed then de-solder it and use a new piece of wire and just one male/female new connection. Option 3 open the box disconnect the cable noting what goes where attach the required length of lead and re-solder the existing socket on the end, presuming it will come apart in the first place.
    [FONT="Arial"]
    Listening is the act of aural discrimination and dissemination of sound


    Voyd the Voyd (slightly modified), SME IV arm(special build virtually a V) and JELCO TK850M(10"), Benz Micro LP-S & Michel Cusis MC cartridge, Furutech AG-12-R4 High Performance Phono Cable, LFD MMC special phono stage, RaspberryPi/HifiBerry Digi to Beresford Caiman SEG DAC, Meridian 508 CD to Caiman SEG, ALLNIC T1500 MKII SET 300B amp, Vienna Acoustics Mozart SE speakers and JBL L100 Century's , Chord Epic speaker leads, & signature links, the Eccose Conductor CA1 cd to pre

  9. #9
    Join Date: May 2016

    Location: wales

    Posts: 450
    I'm peter.

    Default

    Hi A i know what you mean but it is thousands of miles away ,,just thought i would ask,, michell will not make one, just say see the dealer who will not supply one as michell will not make one,, i suppose they are a set length for a reason ,,so the orbe controller will work properly , you can get a fly lead for the gyro but not the orbe

    pete

  10. #10
    Join Date: Nov 2011

    Location: Seaton, Devon, UK

    Posts: 1,856
    I'm Adrian.

    Default

    Quote Originally Posted by gwernaffield View Post
    Hi A i know what you mean but it is thousands of miles away ,,just thought i would ask,, michell will not make one, just say see the dealer who will not supply one as michell will not make one,, i suppose they are a set length for a reason ,,so the orbe controller will work properly , you can get a fly lead for the gyro but not the orbe

    pete
    That sounds very strange.
    [FONT="Arial"]
    Listening is the act of aural discrimination and dissemination of sound


    Voyd the Voyd (slightly modified), SME IV arm(special build virtually a V) and JELCO TK850M(10"), Benz Micro LP-S & Michel Cusis MC cartridge, Furutech AG-12-R4 High Performance Phono Cable, LFD MMC special phono stage, RaspberryPi/HifiBerry Digi to Beresford Caiman SEG DAC, Meridian 508 CD to Caiman SEG, ALLNIC T1500 MKII SET 300B amp, Vienna Acoustics Mozart SE speakers and JBL L100 Century's , Chord Epic speaker leads, & signature links, the Eccose Conductor CA1 cd to pre

+ Reply to Thread



 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •