Quite correct Barry. The differences seem to be in the shielding and insulation. As mentioned, I used GAC-2 V1, p/n 10421: https://gothamcables.com/en/gothamca...og/10421gac2v1
Location: Ontario, Canada
Posts: 791
I'm Svend.
Quite correct Barry. The differences seem to be in the shielding and insulation. As mentioned, I used GAC-2 V1, p/n 10421: https://gothamcables.com/en/gothamca...og/10421gac2v1
well ive just bought these 2 types of cable to have a play.
https://www.ebay.co.uk/itm/Van-Damme...item1ea462ce96
and this,
https://www.ebay.co.uk/itm/Van-Damme...item644b5e208e
My System
John Wood KT88 Amp.
Paradise Phono Stage
Sony TTS-8000 Turntable.
PMAT-1010 MK6 Tonearm.
Ortofon Cadenza Bronze
Sony X555ES Cd Player
Yamaha NS1000m Speakers
Location: Ontario, Canada
Posts: 791
I'm Svend.
Good one Jamie. It will be interesting to hear your impressions of the two.
The twisted pair one is curious, in that it seems that one conductor has 7 x 0.1mm strands, and the second has 21 x 0.1mm strands. I've not seen that before. You'll have to pay attention to which is supply and which is return. And how do you plan to solder the shield? Most layups have the shield joined with the return conductor at the source end, and the shield is cut short (not joined) at the preamp/amp end. At least that's how I learned to do it; I think others here do the same(?)
Best of luck with the project.
Svend
cheers svend,
i went with that one because j7 uses it for tonearm cable,i had my zeta rewired a while back and always like the sound.
yep i'll use the shield connected at the source end only.
My System
John Wood KT88 Amp.
Paradise Phono Stage
Sony TTS-8000 Turntable.
PMAT-1010 MK6 Tonearm.
Ortofon Cadenza Bronze
Sony X555ES Cd Player
Yamaha NS1000m Speakers
Location: Ontario, Canada
Posts: 791
I'm Svend.
Good one Jamie. I'll have to keep that stuff in mind for when I build up a phono cable. I was thinking of using some Mogami 2534 that I have on hand, but am open to other options. Thanks for that!
Svend
Had both.
The LoCap stuff is the only Van Damme cable I've ever liked. It's got a lot of quality, unfortunately I found the top end a bit too hot for my taste. It's also a right bitch to get in any RCAs other than the MSAUDIO ones or those of similar design for large diameter cables.
The other one I've used as Interconnects and tonearm cable. Does a reasonable job but the bass was flabby and under controlled.
Obviously these are just my experiences and yours may differ. Fair play for having a go
Sent from my VKY-L09 using Tapatalk
My System
John Wood KT88 Amp.
Paradise Phono Stage
Sony TTS-8000 Turntable.
PMAT-1010 MK6 Tonearm.
Ortofon Cadenza Bronze
Sony X555ES Cd Player
Yamaha NS1000m Speakers
Just out of interest - what do you mean by 'coax' ?
I automatically think of aerial/cable TV connector lead - which seems like an impossible wrestle with any RCA connector - or alternatively the 75ohm stuff that's used for SPDIF connection (which I have tried as analogue cable)
Location: Ontario, Canada
Posts: 791
I'm Svend.
Mike, coax is a single central conductor surrounded by insulation and then a shield of some kind (either spiral wrap or braided). The centre conductor carries the signal and is soldered to the centre pin of the RCA plug. The shield is unwrapped for a short length, then gathered together and twisted to form a single "rope" of wire; this is then soldered to the negative shell of the RCA and serves as the return conductor. So you are quite right, the cable is the same basic layup as that for TV lead.
Hope this makes sense...
Svend