I was thinking along the lines of carpet tape but if any of you have any ideas I would welcome them.
I was thinking along the lines of carpet tape but if any of you have any ideas I would welcome them.
SS
CD Teac VRDS25X(Audiotuned) DECK 1210 Mat Crystal Audio Mods MN Base/Bearing/Platter+Ebony armboard Feet Isonoe PSU Paul Hynes SR7EHD-27XL/DCSXL Ag DC lead/3 Stage Regs/Recap PCB+No Pitch/Strobe/Light ARM SME V(Kondo Ag Rewire&Tags) MC Cadenza Black FGS CABLES Arm Yannis SPD-4 IC Yannis 222 Litz+Ag bullets Power WAR PRE ATC SCA2 SPEAKERS ATC 50ASL STANDS Atacama PHONO Sugden Masterclass PA4 SUT Ortofon ST80SE POWER PSAudio P10
VALVE
PRE Croft Epoch(Modded) AMP Sondex S100 (Modded) SPEAKERS Tannoy 15"MG+RFC Warwick cabs+ Ref XO + Batpure supertweeters DECK Garrard 301 Mat Teunto Bearings 401(Bastin) Plinth Bamboo Arms 3009/3012 PSU Eagle+Tachometer MC Ag Meister II/FGS + Ortofon SPU MONO CABLES Arm Yannis 420.5 Litz+ SpeakerPC Tripple C+WBT-0681 Ag IC Oyaide FTVS-510 AgWBT 0110Ag Phonostages Paradise(4 Box Mega-Modded) / Croft Musicmaker
What do you want to stick, 3M does lots of material specific tapes. I have some 3M tape on 0.5mm foam if that's any good for your needs. Little bit of shear damping when used, great between heavy flat items.
Kuzma Stabi/S 12", (LP12-bastard) DC motor and optical tacho psu, Benz LP, Paradise (phonostage). MB-Pro, Brooklyn dac and psu, Bruno Putzeys balanced pre, mod86p dual mono amps, Yamaha NS1000m
https://www.vikingtapes.co.uk/produc...SABEgLYo_D_BwE
Fantastic stuff
Auto trade type used for attaching badges etc. to cars. It's the best!
Some is foam about 1mm thick, some is just thin.
Thanks lads. I'm experimenting with with tonearm boards on my Lenco 75. I'm making CLD variants. I want the tape to bond the boards to the 75's top plate. I just bought some Gorilla tape.
SS
CD Teac VRDS25X(Audiotuned) DECK 1210 Mat Crystal Audio Mods MN Base/Bearing/Platter+Ebony armboard Feet Isonoe PSU Paul Hynes SR7EHD-27XL/DCSXL Ag DC lead/3 Stage Regs/Recap PCB+No Pitch/Strobe/Light ARM SME V(Kondo Ag Rewire&Tags) MC Cadenza Black FGS CABLES Arm Yannis SPD-4 IC Yannis 222 Litz+Ag bullets Power WAR PRE ATC SCA2 SPEAKERS ATC 50ASL STANDS Atacama PHONO Sugden Masterclass PA4 SUT Ortofon ST80SE POWER PSAudio P10
VALVE
PRE Croft Epoch(Modded) AMP Sondex S100 (Modded) SPEAKERS Tannoy 15"MG+RFC Warwick cabs+ Ref XO + Batpure supertweeters DECK Garrard 301 Mat Teunto Bearings 401(Bastin) Plinth Bamboo Arms 3009/3012 PSU Eagle+Tachometer MC Ag Meister II/FGS + Ortofon SPU MONO CABLES Arm Yannis 420.5 Litz+ SpeakerPC Tripple C+WBT-0681 Ag IC Oyaide FTVS-510 AgWBT 0110Ag Phonostages Paradise(4 Box Mega-Modded) / Croft Musicmaker
Location: South Yorkshire
Posts: 29
I'm Dave.
This stuff is pretty good too, about 1-2mm thick. Whichever you use, you will need to clean and degrease the surfaces thoroughly. I used some Coleman fuel (heptane, no oil in it) when I stuck the number plate back on my car. IPA wasn't enough to remove wax residue.
https://www.sealantsandtoolsdirect.c...YaAh7wEALw_wcB