Last edited by farflungstar; 03-05-2018 at 21:18.
Technics SP10 mk2
Jan Allaerts MC 1 Boron mk1 cart
Miyajima Shilabe cart
Hashimoto HM-X SUT
Siggwan (gimballed not unipivot) Cocobola 12"
Aurorasound Vida LCR Phonostage
The Truth linestage
Dave Slagle Autoformer Volume Controller
Cary 805c SET amps
Audio Note ANe-SPX speakers
Townshend Isolda speaker cables
Cardas Golden Presence interconnects
Location: London
Posts: 685
I'm James.
Sounds like the pre is behaving itself. Panic over
Sent from my GT-I9195 using Tapatalk
I concur, good to go Adrian
Location: London
Posts: 685
I'm James.
It might indeed! It would help to know what pre it is, otherwise we all go round in circles. Also do the Jfets occur after the input tube, or is it a driver? If the former I'd be inclined to look at the 6H30P tubes, in my experience they can misbehave if stressed.
Sent from my GT-I9195 using Tapatalk
This is my worry. I really can't say for absolutely sure what caused it (the techie said it was DC at the input) - but what other equipment did it? The problem came up (or was very apparent) when I bought that ill fated CDP and connected it direct to the amp using its inbuilt volume. That was returned but I cannot be 100% sure it was the cause.
I checked the DC at the outputs of the truth pre after the techie told me about the DC - one channel (at the 200m setting) was 00.2 the other 01.7 - but had I checked it at the 2000 setting I don't know what that would have been. For this reason I contacted the maker (who said it was negligible and not likely to cause any issue) and adjusted the input buffers and output buffers to 0 on both channels using the 200m setting on the meter. In theory there is no DC in the circuit except perhaps the anomoly of bad probe contacts on the outputs when measuring.
The truth is never switched off and I never connect or disconnect stuff when things are switched on. The only components are the cart, Vida, hashimoto, truth, ref 75, Tannoys.
Is there a possibility that the small input tubes in the 75 could have an effect? It was soak tested using them at the centre without a problem but I have a brand new set of power and signal tubes.
It's silly but I still haven't switched the amp on - I just dare not.
The truth has caused no problems with the Hiraga amp but of course it's a different animal to the ARC.
Last edited by farflungstar; 04-05-2018 at 12:41.
Technics SP10 mk2
Jan Allaerts MC 1 Boron mk1 cart
Miyajima Shilabe cart
Hashimoto HM-X SUT
Siggwan (gimballed not unipivot) Cocobola 12"
Aurorasound Vida LCR Phonostage
The Truth linestage
Dave Slagle Autoformer Volume Controller
Cary 805c SET amps
Audio Note ANe-SPX speakers
Townshend Isolda speaker cables
Cardas Golden Presence interconnects
Location: Suffolk, UK
Posts: 1,473
I'm Paul.
Can you advise your setup, is it the same as in your signature? It looks like your Truth phono amp is connected via the poweramp via a transformer based volume control/preamp? If this is the case any DC on the output of the Truth will effectively be blocked by the volume control as transformers do not pass DC. However, out of hearing band oscillation could be passed on to the poweramp.
Many multimeters dont tend to be good at measuring at the frequency extremes but you could try measuring the Truth’s outputs with the lowest AC volts setting with and without the inputs grounded.
~Paul~
It's simple - Vida phono stage into hashimoto sut into Truth ldr pre into amp - no transformers. Though now I wish I still had the old slagle autoformers....
Technics SP10 mk2
Jan Allaerts MC 1 Boron mk1 cart
Miyajima Shilabe cart
Hashimoto HM-X SUT
Siggwan (gimballed not unipivot) Cocobola 12"
Aurorasound Vida LCR Phonostage
The Truth linestage
Dave Slagle Autoformer Volume Controller
Cary 805c SET amps
Audio Note ANe-SPX speakers
Townshend Isolda speaker cables
Cardas Golden Presence interconnects
One more doubt - I bought the 75 second hand, and the CDP shortly afterwards - there is the possibility that the ref 75 was faulty when I bought it - this is the problem - so manyy variables I feel like dumping the lot.
I just remeasured the pre outputs having rigged up an RCA plug to the meter probes. Right 000 left -000 - set at 2000m. At 200m I get right 00.4 left -00.2.
I have replaced ALL tubes with new.
Should I try it?
Last edited by farflungstar; 04-05-2018 at 14:04.
Technics SP10 mk2
Jan Allaerts MC 1 Boron mk1 cart
Miyajima Shilabe cart
Hashimoto HM-X SUT
Siggwan (gimballed not unipivot) Cocobola 12"
Aurorasound Vida LCR Phonostage
The Truth linestage
Dave Slagle Autoformer Volume Controller
Cary 805c SET amps
Audio Note ANe-SPX speakers
Townshend Isolda speaker cables
Cardas Golden Presence interconnects
Location: London
Posts: 685
I'm James.
If you know of anyone with an oscilloscope then it might be worth looking for ultrasonics which might be there as Andrew has suggested? It seems a long shot but safety is always sensible. If not and you are worried then perhaps get a cheap charity shop type amp and use that as a burner to see if any issues arise?
Website: http://www.homehifi.co.uk
Website: http://www.beresford.me
Website: http://www.homehifi.asia