Here's the USA customer deck pic of his Technics SP-10 with slate bed and the sizeable solid ebony armboard I made for him.
Always nice to see where these creations end up.
Here's the USA customer deck pic of his Technics SP-10 with slate bed and the sizeable solid ebony armboard I made for him.
Always nice to see where these creations end up.
System: Turntable : SP10 MKII slate plinth, Custom Ebony tonearm board, Arm : Fidelity Research FR64s, Cartridge : SPU Royal N. SUT : Lundahl 1:13. Phonostage : Icon Audio, Streaming RPi/Kali reclocker -> I2S -> DSP XO / Pre / 4 DAC's : WAF Najda, 5 Poweramps : 3 x EL84 SET's, 2 x D class amps on bass channels, Speakers : 5 way front loaded horn system: 2 X Tapped sub 15" LF drivers / 2 X Exponential mid bass 15" drivers / Tractrix 200Hz mid horns with JBL2482's, / Tractrix 550Hz upper wooden horns with factory refurb'd Vitavox S2's / Raal Lazy Ribbons as high frequency tweeters. Wires: good silver or good copper where best suited. DIY RCM.
Maker of tonearm boards, armpods, Tannoy GRF style speaker cabinets, horn speakers, counterweights and more.
For more information about my creations and products please click below
http://fosworld.wixsite.com/magna-audio & on Instagram https://www.instagram.com/magna_audio/
Customer pictures of the solid Ebony armboard for Technics SL-1210GR record deck fitted with Acoustic Signature TA-500 tonearm. Tight but doable.
System: Turntable : SP10 MKII slate plinth, Custom Ebony tonearm board, Arm : Fidelity Research FR64s, Cartridge : SPU Royal N. SUT : Lundahl 1:13. Phonostage : Icon Audio, Streaming RPi/Kali reclocker -> I2S -> DSP XO / Pre / 4 DAC's : WAF Najda, 5 Poweramps : 3 x EL84 SET's, 2 x D class amps on bass channels, Speakers : 5 way front loaded horn system: 2 X Tapped sub 15" LF drivers / 2 X Exponential mid bass 15" drivers / Tractrix 200Hz mid horns with JBL2482's, / Tractrix 550Hz upper wooden horns with factory refurb'd Vitavox S2's / Raal Lazy Ribbons as high frequency tweeters. Wires: good silver or good copper where best suited. DIY RCM.
Maker of tonearm boards, armpods, Tannoy GRF style speaker cabinets, horn speakers, counterweights and more.
For more information about my creations and products please click below
http://fosworld.wixsite.com/magna-audio & on Instagram https://www.instagram.com/magna_audio/
Here's an ebony armboard and fitting job for a gloss black plinthed SP-10.
The thin copper mat, and tall Stax arm and base, meant with the existing MDF veneered armboard was not low enough.
The Stax arm was very interesting. I've not seen one before.
3 interchangeable arm tubes. 2 S shaped and one straight.
Nice setup.
System: Turntable : SP10 MKII slate plinth, Custom Ebony tonearm board, Arm : Fidelity Research FR64s, Cartridge : SPU Royal N. SUT : Lundahl 1:13. Phonostage : Icon Audio, Streaming RPi/Kali reclocker -> I2S -> DSP XO / Pre / 4 DAC's : WAF Najda, 5 Poweramps : 3 x EL84 SET's, 2 x D class amps on bass channels, Speakers : 5 way front loaded horn system: 2 X Tapped sub 15" LF drivers / 2 X Exponential mid bass 15" drivers / Tractrix 200Hz mid horns with JBL2482's, / Tractrix 550Hz upper wooden horns with factory refurb'd Vitavox S2's / Raal Lazy Ribbons as high frequency tweeters. Wires: good silver or good copper where best suited. DIY RCM.
Maker of tonearm boards, armpods, Tannoy GRF style speaker cabinets, horn speakers, counterweights and more.
For more information about my creations and products please click below
http://fosworld.wixsite.com/magna-audio & on Instagram https://www.instagram.com/magna_audio/
Here's an Armpod and counterweight job that made it to Oz in record time (thanks Transglobal Express).
It's an ultra low but larger diameter pod, full of cast lead for high mass.
2 interchangeable armboards, one for Rega 3 point and one for Linn.
Finished in satin black and natural polished ebony.
The stainless steel counterweight is an Alphason heavy work nylon damper insert.
In the making
Turning the feet discs
Heavy counterweight
System: Turntable : SP10 MKII slate plinth, Custom Ebony tonearm board, Arm : Fidelity Research FR64s, Cartridge : SPU Royal N. SUT : Lundahl 1:13. Phonostage : Icon Audio, Streaming RPi/Kali reclocker -> I2S -> DSP XO / Pre / 4 DAC's : WAF Najda, 5 Poweramps : 3 x EL84 SET's, 2 x D class amps on bass channels, Speakers : 5 way front loaded horn system: 2 X Tapped sub 15" LF drivers / 2 X Exponential mid bass 15" drivers / Tractrix 200Hz mid horns with JBL2482's, / Tractrix 550Hz upper wooden horns with factory refurb'd Vitavox S2's / Raal Lazy Ribbons as high frequency tweeters. Wires: good silver or good copper where best suited. DIY RCM.
Maker of tonearm boards, armpods, Tannoy GRF style speaker cabinets, horn speakers, counterweights and more.
For more information about my creations and products please click below
http://fosworld.wixsite.com/magna-audio & on Instagram https://www.instagram.com/magna_audio/
This one was bound for Hong Kong
A super heavyweight record puck in polished ebony and gunmetal.
Features ebony cores sunk into the gunmetal.
System: Turntable : SP10 MKII slate plinth, Custom Ebony tonearm board, Arm : Fidelity Research FR64s, Cartridge : SPU Royal N. SUT : Lundahl 1:13. Phonostage : Icon Audio, Streaming RPi/Kali reclocker -> I2S -> DSP XO / Pre / 4 DAC's : WAF Najda, 5 Poweramps : 3 x EL84 SET's, 2 x D class amps on bass channels, Speakers : 5 way front loaded horn system: 2 X Tapped sub 15" LF drivers / 2 X Exponential mid bass 15" drivers / Tractrix 200Hz mid horns with JBL2482's, / Tractrix 550Hz upper wooden horns with factory refurb'd Vitavox S2's / Raal Lazy Ribbons as high frequency tweeters. Wires: good silver or good copper where best suited. DIY RCM.
Maker of tonearm boards, armpods, Tannoy GRF style speaker cabinets, horn speakers, counterweights and more.
For more information about my creations and products please click below
http://fosworld.wixsite.com/magna-audio & on Instagram https://www.instagram.com/magna_audio/
Here is the low rider wide armpod mounted up in the customer's system in Australia.
Rega RB2000 tonearm.
System: Turntable : SP10 MKII slate plinth, Custom Ebony tonearm board, Arm : Fidelity Research FR64s, Cartridge : SPU Royal N. SUT : Lundahl 1:13. Phonostage : Icon Audio, Streaming RPi/Kali reclocker -> I2S -> DSP XO / Pre / 4 DAC's : WAF Najda, 5 Poweramps : 3 x EL84 SET's, 2 x D class amps on bass channels, Speakers : 5 way front loaded horn system: 2 X Tapped sub 15" LF drivers / 2 X Exponential mid bass 15" drivers / Tractrix 200Hz mid horns with JBL2482's, / Tractrix 550Hz upper wooden horns with factory refurb'd Vitavox S2's / Raal Lazy Ribbons as high frequency tweeters. Wires: good silver or good copper where best suited. DIY RCM.
Maker of tonearm boards, armpods, Tannoy GRF style speaker cabinets, horn speakers, counterweights and more.
For more information about my creations and products please click below
http://fosworld.wixsite.com/magna-audio & on Instagram https://www.instagram.com/magna_audio/
Here's an armboard replication in aluminium. 10mm thick.
From finish to start.
Black lacquer and M3 caphead bolts for SME armbase mounting.
Etch primer phase. This gives a secure base on the aluminium for the top coats of lacquer.
The bare aluminium board. All fitting holes and shaping done
Cut to shape. Alongside the wooden board it will replace
Will be posted off once the lacquer is fully hardened.
System: Turntable : SP10 MKII slate plinth, Custom Ebony tonearm board, Arm : Fidelity Research FR64s, Cartridge : SPU Royal N. SUT : Lundahl 1:13. Phonostage : Icon Audio, Streaming RPi/Kali reclocker -> I2S -> DSP XO / Pre / 4 DAC's : WAF Najda, 5 Poweramps : 3 x EL84 SET's, 2 x D class amps on bass channels, Speakers : 5 way front loaded horn system: 2 X Tapped sub 15" LF drivers / 2 X Exponential mid bass 15" drivers / Tractrix 200Hz mid horns with JBL2482's, / Tractrix 550Hz upper wooden horns with factory refurb'd Vitavox S2's / Raal Lazy Ribbons as high frequency tweeters. Wires: good silver or good copper where best suited. DIY RCM.
Maker of tonearm boards, armpods, Tannoy GRF style speaker cabinets, horn speakers, counterweights and more.
For more information about my creations and products please click below
http://fosworld.wixsite.com/magna-audio & on Instagram https://www.instagram.com/magna_audio/
Progress catch-up on a pair of mid bass horns I'm making.
They will be used in a 4/5 way full spectrum horn system.
18mm premium birch plywood.
1.2m long. Exponential horn flare.
Frequency usage 100Hz to 400Hz.
Eminence Kappa 12A 12" bass drivers.
Driver chamber and bracing to do.
These will fine articulate, fast and tuneful mid bass.
System: Turntable : SP10 MKII slate plinth, Custom Ebony tonearm board, Arm : Fidelity Research FR64s, Cartridge : SPU Royal N. SUT : Lundahl 1:13. Phonostage : Icon Audio, Streaming RPi/Kali reclocker -> I2S -> DSP XO / Pre / 4 DAC's : WAF Najda, 5 Poweramps : 3 x EL84 SET's, 2 x D class amps on bass channels, Speakers : 5 way front loaded horn system: 2 X Tapped sub 15" LF drivers / 2 X Exponential mid bass 15" drivers / Tractrix 200Hz mid horns with JBL2482's, / Tractrix 550Hz upper wooden horns with factory refurb'd Vitavox S2's / Raal Lazy Ribbons as high frequency tweeters. Wires: good silver or good copper where best suited. DIY RCM.
Maker of tonearm boards, armpods, Tannoy GRF style speaker cabinets, horn speakers, counterweights and more.
For more information about my creations and products please click below
http://fosworld.wixsite.com/magna-audio & on Instagram https://www.instagram.com/magna_audio/
Simon of Simon Mears Audio asked me to make an improved jig to hold spokeshave blades during sharpening.
9mm brass was chosen.
Various shapings, drillings and fittings.
System: Turntable : SP10 MKII slate plinth, Custom Ebony tonearm board, Arm : Fidelity Research FR64s, Cartridge : SPU Royal N. SUT : Lundahl 1:13. Phonostage : Icon Audio, Streaming RPi/Kali reclocker -> I2S -> DSP XO / Pre / 4 DAC's : WAF Najda, 5 Poweramps : 3 x EL84 SET's, 2 x D class amps on bass channels, Speakers : 5 way front loaded horn system: 2 X Tapped sub 15" LF drivers / 2 X Exponential mid bass 15" drivers / Tractrix 200Hz mid horns with JBL2482's, / Tractrix 550Hz upper wooden horns with factory refurb'd Vitavox S2's / Raal Lazy Ribbons as high frequency tweeters. Wires: good silver or good copper where best suited. DIY RCM.
Maker of tonearm boards, armpods, Tannoy GRF style speaker cabinets, horn speakers, counterweights and more.
For more information about my creations and products please click below
http://fosworld.wixsite.com/magna-audio & on Instagram https://www.instagram.com/magna_audio/
Progress on the large midbass horn project.
Now there are two and mouth surround is fabricated.
They will be used in a 4/5 way full spectrum horn system.
18mm premium birch plywood.
1.2m long. Exponential horn flare.
Frequency usage 100Hz to 400Hz.
Eminence Kappa 12A 12" bass drivers.
Driver chamber and bracing to do.
These will fine articulate, fast and tuneful mid bass.
System: Turntable : SP10 MKII slate plinth, Custom Ebony tonearm board, Arm : Fidelity Research FR64s, Cartridge : SPU Royal N. SUT : Lundahl 1:13. Phonostage : Icon Audio, Streaming RPi/Kali reclocker -> I2S -> DSP XO / Pre / 4 DAC's : WAF Najda, 5 Poweramps : 3 x EL84 SET's, 2 x D class amps on bass channels, Speakers : 5 way front loaded horn system: 2 X Tapped sub 15" LF drivers / 2 X Exponential mid bass 15" drivers / Tractrix 200Hz mid horns with JBL2482's, / Tractrix 550Hz upper wooden horns with factory refurb'd Vitavox S2's / Raal Lazy Ribbons as high frequency tweeters. Wires: good silver or good copper where best suited. DIY RCM.
Maker of tonearm boards, armpods, Tannoy GRF style speaker cabinets, horn speakers, counterweights and more.
For more information about my creations and products please click below
http://fosworld.wixsite.com/magna-audio & on Instagram https://www.instagram.com/magna_audio/