+ Reply to Thread
Page 40 of 40 FirstFirst ... 30383940
Results 391 to 394 of 394

Thread: Magna Audio News & Product Updates

  1. #391
    Join Date: Mar 2009

    Location: The New Forest

    Posts: 1,666
    I'm Steve.

    Default

    Audio Technica 1503 tonearm armlift holder/mount

    Super shiny final/fine polishing done.
    This bespoke Audio Technica 1503 tonearm armlift holder/mount is ready.
    Made from solid stainless steel 6mm thick plate.

    Double grubscrews on both the armpillar and Jelco arm lift.
    An elegant solution to easy and safe cueing.

    Using a Jelco armlift and Audio Technical arm clip.

    It cleverly allows the use of the anti-skate mechanism too

    Pics show finished article back to raw 6mm stainless steel plate





    Test fitting before polishing



    Spinning up for machining the mounting holes



    Raw 6mm SS plate, rough shaped

    System: Turntable : SP10 MKII slate plinth, Custom Ebony tonearm board, Arm : Fidelity Research FR64s, Cartridge : SPU Royal N. SUT : Lundahl 1:13. Phonostage : Icon Audio, Streaming RPi/Kali reclocker -> I2S -> DSP XO / Pre / 4 DAC's : WAF Najda, 5 Poweramps : 3 x EL84 SET's, 2 x D class amps on bass channels, Speakers : 5 way front loaded horn system: 2 X Tapped sub 15" LF drivers / 2 X Exponential mid bass 15" drivers / Tractrix 200Hz mid horns with JBL2482's, / Tractrix 550Hz upper wooden horns with factory refurb'd Vitavox S2's / Raal Lazy Ribbons as high frequency tweeters. Wires: good silver or good copper where best suited. DIY RCM.

    Maker of tonearm boards, armpods, Tannoy GRF style speaker cabinets, horn speakers, counterweights and more.
    For more information about my creations and products please click below

    http://fosworld.wixsite.com/magna-audio & on Instagram https://www.instagram.com/magna_audio/

  2. #392
    Join Date: Mar 2009

    Location: The New Forest

    Posts: 1,666
    I'm Steve.

    Default

    A little fix for a broken Fidelity Research FR64s / FR66s tonearm.

    This is a replacement fit for the lateral weight mounting rod - these do seem to get sheared off.
    No easy way to remove the sheared off bit / replace sometimes.

    I make a very thin walled sleeve that fits over the arms lateral weight mounting position. This can be hobby glued in place by the customer and the lateral weight used as normal.

    Pictured here, with and without my own lateral weight - testing the fit.

    Also a pic of the raw stainlesssteel bar.

    Matching finish to the original.
    Off to the USA soon.








    System: Turntable : SP10 MKII slate plinth, Custom Ebony tonearm board, Arm : Fidelity Research FR64s, Cartridge : SPU Royal N. SUT : Lundahl 1:13. Phonostage : Icon Audio, Streaming RPi/Kali reclocker -> I2S -> DSP XO / Pre / 4 DAC's : WAF Najda, 5 Poweramps : 3 x EL84 SET's, 2 x D class amps on bass channels, Speakers : 5 way front loaded horn system: 2 X Tapped sub 15" LF drivers / 2 X Exponential mid bass 15" drivers / Tractrix 200Hz mid horns with JBL2482's, / Tractrix 550Hz upper wooden horns with factory refurb'd Vitavox S2's / Raal Lazy Ribbons as high frequency tweeters. Wires: good silver or good copper where best suited. DIY RCM.

    Maker of tonearm boards, armpods, Tannoy GRF style speaker cabinets, horn speakers, counterweights and more.
    For more information about my creations and products please click below

    http://fosworld.wixsite.com/magna-audio & on Instagram https://www.instagram.com/magna_audio/

  3. #393
    Join Date: Mar 2009

    Location: The New Forest

    Posts: 1,666
    I'm Steve.

    Default

    A brass extra heavy counterweight for a Acoustic Research XA tonearm.
    130g, delrin damper insert.
    Used a little 4 jaw chuck for the off centre arm mounting hole.

    Off to the USA.











    System: Turntable : SP10 MKII slate plinth, Custom Ebony tonearm board, Arm : Fidelity Research FR64s, Cartridge : SPU Royal N. SUT : Lundahl 1:13. Phonostage : Icon Audio, Streaming RPi/Kali reclocker -> I2S -> DSP XO / Pre / 4 DAC's : WAF Najda, 5 Poweramps : 3 x EL84 SET's, 2 x D class amps on bass channels, Speakers : 5 way front loaded horn system: 2 X Tapped sub 15" LF drivers / 2 X Exponential mid bass 15" drivers / Tractrix 200Hz mid horns with JBL2482's, / Tractrix 550Hz upper wooden horns with factory refurb'd Vitavox S2's / Raal Lazy Ribbons as high frequency tweeters. Wires: good silver or good copper where best suited. DIY RCM.

    Maker of tonearm boards, armpods, Tannoy GRF style speaker cabinets, horn speakers, counterweights and more.
    For more information about my creations and products please click below

    http://fosworld.wixsite.com/magna-audio & on Instagram https://www.instagram.com/magna_audio/

  4. #394
    Join Date: Mar 2009

    Location: The New Forest

    Posts: 1,666
    I'm Steve.

    Default

    Another counterweight.
    This time a super heavyweight for a SME 3012 in Australia.

    Lacquered to give a similar finish and sheen.

    It features double underside grub screws.



    System: Turntable : SP10 MKII slate plinth, Custom Ebony tonearm board, Arm : Fidelity Research FR64s, Cartridge : SPU Royal N. SUT : Lundahl 1:13. Phonostage : Icon Audio, Streaming RPi/Kali reclocker -> I2S -> DSP XO / Pre / 4 DAC's : WAF Najda, 5 Poweramps : 3 x EL84 SET's, 2 x D class amps on bass channels, Speakers : 5 way front loaded horn system: 2 X Tapped sub 15" LF drivers / 2 X Exponential mid bass 15" drivers / Tractrix 200Hz mid horns with JBL2482's, / Tractrix 550Hz upper wooden horns with factory refurb'd Vitavox S2's / Raal Lazy Ribbons as high frequency tweeters. Wires: good silver or good copper where best suited. DIY RCM.

    Maker of tonearm boards, armpods, Tannoy GRF style speaker cabinets, horn speakers, counterweights and more.
    For more information about my creations and products please click below

    http://fosworld.wixsite.com/magna-audio & on Instagram https://www.instagram.com/magna_audio/

+ Reply to Thread
Page 40 of 40 FirstFirst ... 30383940

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •