The ALLO Audio music steamer - Pic heavy review

Quote:

---

Originally Posted by r100

1+ for Moode 3.1

I (think) I noticed that the sound actually "opens up" after a week or so. My boards have been running almost non-stop for the past days and I'm very surprised at the robustness of the Moode 3.1 software which hasn't dropped a frame since I started the run-in.. I also used the max. up-sampling rate for a day or two to find out how the Pi3 would handle the beating and it barely got over 40°C @ around 8-11% of cpu usage according to the "Audio Info" window in Moode :carrot:

---

Upsampling to 384kHz in Moode 3.1 using the Advanced Kernel setting will bypass the Piano DAC chip's internal digital filters (which some reckon to be a weak point). Sounds good to me. :)

With the caveat that I don't really understand how these things work I just put them together and follow the instructions! Wouldn't putting it up to 384kHz mean the Kali wouldn't work as that maxes out at 192 according to the spec? If that's not the case 24 or 32 bit?

could well be ... i just did it to test the Pi3 .. the 192k LED (if I remember) on the
kali was blinking, so you're probably right.

Quote:

---

Originally Posted by r100

could well be ... i just did it to test the Pi3 .. the 192k LED (if I remember) on the
kali was blinking, so you're probably right.

---

If that is the case, is there a way of defeating the filters without maxing out the up sampling i.e. an off switch? It strikes me they might be a bit like tone controls that I said goodbye to in nineteen eighty something!

Quote:

---

Originally Posted by r100

could well be ... i just did it to test the Pi3 .. the 192k LED (if I remember) on the
kali was blinking, so you're probably right.

---

The blue light only flashes for a short time then it stops.

Buffering?

Quote:

---

Originally Posted by Lunicycle

With the caveat that I don't really understand how these things work I just put them together and follow the instructions! Wouldn't putting it up to 384kHz mean the Kali wouldn't work as that maxes out at 192 according to the spec? If that's not the case 24 or 32 bit?

---

According to the sales page on Volumio, the 44/48MHz version (which is the only one sold now) will go up to 384kHz. The Moode 'Audio Info' certainly shows that's happening.
There's no other way of defeating the filters, and they only work way up in the ultrasonic region to keep those frequencies out of amps that don't like them.

Thanks for that. Does that mean that if I upsample to 384kHz that it will keep teenagers and animals out of the room? :)

:D. Maybe thats why i get fewer visits :lol: Here was me thinking i had bo

Hi, this is what my board is doing when fed 32bit / 352.8 kHz or 32 bit / 384 kHz respectively. The LED's are continuously blinking either blue or green.
The postman just came with a packet between his legs and his fingers in his ears, I wonder why ??
;)



https://www.dropbox.com/s/6j734w879b...52-x.jpg?raw=1
https://www.dropbox.com/s/dh2whbok33...4k-x.jpg?raw=1

https://www.dropbox.com/s/12jc5cyqoo...nual.png?raw=1


https://www.allo.com/documents/spark...ech-Manual.pdf

Quote:

---

Originally Posted by r100

Hi, this is what my board is doing when fed 32bit / 352.8 kHz or 32 bit / 384 kHz respectively. The LED's are continuously blinking either blue or green.
The postman just came with a packet between his legs and his fingers in his ears, I wonder why ??
;)

---

According to the TI datasheet, there's an upsampling bypass at 384kHz, but no mention of 352.8kHz.
Never mind the postman, are bats flocking to have a listen? That's the real test.