scoobs
26-11-2008, 16:33
I have the following analogue goodies for sale, due to purchase of a new turntable.
KAB modified SL1210 Mk5SE. (see below for details) £450 delivered to UK.
Zupreme 12g Alloy headshell, high grade OFC litz headshell leads. SME fitting, £35. SOLD
Glanz 9g alloy headshell. Rare, SME fitting, £15
Vintage Denon headshell, no headshell leads. SME fitting. £15
Audio Origami OFC/silver cocktail Tonearm cable with right angle Cardas din plug and modified gold RCA plugs, 60cm. £65
Audio Origami OFC/silver cocktail RCA-RCA interconnects. 40cm. £30
The 1210 has been much discussed on here and other fora, so I wont go into great detail, but it is a serious piece of kit that will embarass a whole lot of decks that cost considerably more, the arm re-wire and psu bringing considerable gains over the stock deck, I know this because I have a stock 1210 that was bought recently with a view to some developing some plinth mods, this plan is now shelved.
The 1210 was bought new and imported in January this year. The mods consist of:
External PSU
Cardas re-wired tonearm
Cardas 5 pin DIN socket this is technically and aesthetically preferable to the phono box option that is appended to the rear of the deck and does not require any soldering to remove/replace.
Tonearm fluid damper
Strobe light disabler
This deck requires a right angle DIN tonearm cable.
The deck comes with custom heavy brass counterweights made by Thrunobulax. These allow greater flexibility with cartridges, and increase the mass which is essential when using the heavy alloy headshells like the Zupreme & Sumiko etc.
The deck is for sale with the stock headshell, and counterweight and Technics 5mm audiophile turntable mat.
NOTE the RDC puck in the image is NOT included. The wooden plinth surround is available separately.
I have added a modification of my own by replacing the stock feet with threaded RDC 1 cones, although should you want the stock feet replaced, just say.
Both the deck and lid is in excellent condition and comes with original box.
http://i230.photobucket.com/albums/ee15/indypepa/hi-fi-again-005.jpg
Also for sale:
Solid Beech isolation base / plinth surround. As seen in picture. This box is my DIY effort at killing seismic vibrations and does the job admirably with silver sand and a 1” granite slab. I had the granite slab cut for this box and it fits snugly without contacting the sides. The box can be used with any type of isolation material you can think up, I have used pipe isolation foam cut in half, a bicycle inner tube and sand. I’m looking for £50 cash on collection is the only option with this, due to weight.
Thanks
KAB modified SL1210 Mk5SE. (see below for details) £450 delivered to UK.
Zupreme 12g Alloy headshell, high grade OFC litz headshell leads. SME fitting, £35. SOLD
Glanz 9g alloy headshell. Rare, SME fitting, £15
Vintage Denon headshell, no headshell leads. SME fitting. £15
Audio Origami OFC/silver cocktail Tonearm cable with right angle Cardas din plug and modified gold RCA plugs, 60cm. £65
Audio Origami OFC/silver cocktail RCA-RCA interconnects. 40cm. £30
The 1210 has been much discussed on here and other fora, so I wont go into great detail, but it is a serious piece of kit that will embarass a whole lot of decks that cost considerably more, the arm re-wire and psu bringing considerable gains over the stock deck, I know this because I have a stock 1210 that was bought recently with a view to some developing some plinth mods, this plan is now shelved.
The 1210 was bought new and imported in January this year. The mods consist of:
External PSU
Cardas re-wired tonearm
Cardas 5 pin DIN socket this is technically and aesthetically preferable to the phono box option that is appended to the rear of the deck and does not require any soldering to remove/replace.
Tonearm fluid damper
Strobe light disabler
This deck requires a right angle DIN tonearm cable.
The deck comes with custom heavy brass counterweights made by Thrunobulax. These allow greater flexibility with cartridges, and increase the mass which is essential when using the heavy alloy headshells like the Zupreme & Sumiko etc.
The deck is for sale with the stock headshell, and counterweight and Technics 5mm audiophile turntable mat.
NOTE the RDC puck in the image is NOT included. The wooden plinth surround is available separately.
I have added a modification of my own by replacing the stock feet with threaded RDC 1 cones, although should you want the stock feet replaced, just say.
Both the deck and lid is in excellent condition and comes with original box.
http://i230.photobucket.com/albums/ee15/indypepa/hi-fi-again-005.jpg
Also for sale:
Solid Beech isolation base / plinth surround. As seen in picture. This box is my DIY effort at killing seismic vibrations and does the job admirably with silver sand and a 1” granite slab. I had the granite slab cut for this box and it fits snugly without contacting the sides. The box can be used with any type of isolation material you can think up, I have used pipe isolation foam cut in half, a bicycle inner tube and sand. I’m looking for £50 cash on collection is the only option with this, due to weight.
Thanks