Trade: Magna Audio
Location: The New Forest
Posts: 1,861
I'm Steve.
I was approached to make the 3 arm balancing counter weights, anti-skate weight and lateral weight for a Dynavector DV-505 arm, needed to complete the arm, as these had gone missing.
These were made to original weight specification.
and the lateral weight
Last edited by Magna Audio; 28-10-2017 at 22:46.
System: Turntable : SP10 MKII slate plinth, Custom Ebony tonearm board, Arm : Fidelity Research FR64s, Cartridge : SPU Royal N. SUT : Lundahl 1:13. Phonostage : Icon Audio, Streaming RPi/Kali reclocker -> I2S -> DSP XO / Pre / 4 DAC's : WAF Najda, 5 Poweramps : 3 x EL84 SET's, 2 x D class amps on bass channels, Speakers : 5 way front loaded horn system: 2 X Tapped sub 15" LF drivers / 2 X Exponential mid bass 15" drivers / Tractrix 200Hz mid horns with JBL2482's, / Tractrix 550Hz upper wooden horns with factory refurb'd Vitavox S2's / Raal Lazy Ribbons as high frequency tweeters. Wires: good silver or good copper where best suited. DIY RCM.
Maker of tonearm boards, armpods, Tannoy GRF style speaker cabinets, horn speakers, counterweights and more.
For more information about my creations and products please click below
http://fosworld.wixsite.com/magna-audio & on Instagram https://www.instagram.com/magna_audio/
New Member
Location: Montreal Canada
Posts: 21
I'm Maurice.
hello Steve,
did you ever get a request for the Sansui SR-929 lateral weight with the post?
thank you
Mcintosh MC-2505, C-28, MR74 Sansui SR-929 and a Thorens TD160 speakers are Vandersteen C2e, Chartwell PM400 and dynaco A25 XL cartridges are AT signet TK7e and a Shure 97xe with a SAS stylus.
Trade: Magna Audio
Location: The New Forest
Posts: 1,861
I'm Steve.
Hi,Originally Posted by Sillver79
I did and I did reply to it. Perhaps email trouble somewhere along the line. Sorry for that.
I will dig out my reply and send via PM.
Best regards,
Steve
System: Turntable : SP10 MKII slate plinth, Custom Ebony tonearm board, Arm : Fidelity Research FR64s, Cartridge : SPU Royal N. SUT : Lundahl 1:13. Phonostage : Icon Audio, Streaming RPi/Kali reclocker -> I2S -> DSP XO / Pre / 4 DAC's : WAF Najda, 5 Poweramps : 3 x EL84 SET's, 2 x D class amps on bass channels, Speakers : 5 way front loaded horn system: 2 X Tapped sub 15" LF drivers / 2 X Exponential mid bass 15" drivers / Tractrix 200Hz mid horns with JBL2482's, / Tractrix 550Hz upper wooden horns with factory refurb'd Vitavox S2's / Raal Lazy Ribbons as high frequency tweeters. Wires: good silver or good copper where best suited. DIY RCM.
Maker of tonearm boards, armpods, Tannoy GRF style speaker cabinets, horn speakers, counterweights and more.
For more information about my creations and products please click below
http://fosworld.wixsite.com/magna-audio & on Instagram https://www.instagram.com/magna_audio/
Trade: Magna Audio
Location: The New Forest
Posts: 1,861
I'm Steve.
Here's an Ebony armboard bound for a SL-1210. Drilled for a Jelco SA750D tonearm and provisioned with extra deep mounting surface for the 'Shuggie' upgrade Jelco armbase.
Last edited by Magna Audio; 28-10-2017 at 22:40.
System: Turntable : SP10 MKII slate plinth, Custom Ebony tonearm board, Arm : Fidelity Research FR64s, Cartridge : SPU Royal N. SUT : Lundahl 1:13. Phonostage : Icon Audio, Streaming RPi/Kali reclocker -> I2S -> DSP XO / Pre / 4 DAC's : WAF Najda, 5 Poweramps : 3 x EL84 SET's, 2 x D class amps on bass channels, Speakers : 5 way front loaded horn system: 2 X Tapped sub 15" LF drivers / 2 X Exponential mid bass 15" drivers / Tractrix 200Hz mid horns with JBL2482's, / Tractrix 550Hz upper wooden horns with factory refurb'd Vitavox S2's / Raal Lazy Ribbons as high frequency tweeters. Wires: good silver or good copper where best suited. DIY RCM.
Maker of tonearm boards, armpods, Tannoy GRF style speaker cabinets, horn speakers, counterweights and more.
For more information about my creations and products please click below
http://fosworld.wixsite.com/magna-audio & on Instagram https://www.instagram.com/magna_audio/
Senior Member
Location: Wales, UK
Posts: 315
I'm Simon.
Beautifully made and sounding great. Bass is noticeably more tuneful and vocals never sounded better in my system- ssssibilance is now a thing of the past. Highly recommended
Simon.
Top Ranking Member
Location: London
Posts: 4,419
I'm Robert.
Yes, The Ebony armboard is just excellent !!Beautifully made and sounding great. Bass is noticeably more tuneful and vocals never sounded better in my system- ssssibilance is now a thing of the past. Highly recommended
Trade: Magna Audio
Location: The New Forest
Posts: 1,861
I'm Steve.
Thanks Robbie.
Here is an update to the armboard / pod I made for a customer a while back.
The original armboard for the lead filled stand alone arm pod I supplied was for a Fidelity Research FR64s arm.
It had to be shallow as the arm is quite high and there was not a lot of height overall to play with.
The Schick 12" arm is much lower so a thicker solid ebony armboard could be fitted.
Here is the base and board
Test mounted on the pod ready to go.
Last edited by Magna Audio; 28-10-2017 at 22:38.
System: Turntable : SP10 MKII slate plinth, Custom Ebony tonearm board, Arm : Fidelity Research FR64s, Cartridge : SPU Royal N. SUT : Lundahl 1:13. Phonostage : Icon Audio, Streaming RPi/Kali reclocker -> I2S -> DSP XO / Pre / 4 DAC's : WAF Najda, 5 Poweramps : 3 x EL84 SET's, 2 x D class amps on bass channels, Speakers : 5 way front loaded horn system: 2 X Tapped sub 15" LF drivers / 2 X Exponential mid bass 15" drivers / Tractrix 200Hz mid horns with JBL2482's, / Tractrix 550Hz upper wooden horns with factory refurb'd Vitavox S2's / Raal Lazy Ribbons as high frequency tweeters. Wires: good silver or good copper where best suited. DIY RCM.
Maker of tonearm boards, armpods, Tannoy GRF style speaker cabinets, horn speakers, counterweights and more.
For more information about my creations and products please click below
http://fosworld.wixsite.com/magna-audio & on Instagram https://www.instagram.com/magna_audio/
Trade: Magna Audio
Location: The New Forest
Posts: 1,861
I'm Steve.
Here's a little job for germbox
He was looking to balance a DL103 and heavy AT headshell and also needed spacers to get the VTA right.
Full thread here
http://theartofsound.net/forum/showt...ghlight=spacer
I made him a 142g Stainless steel counterweight and headshell to cartridge spacers in ebony at 3.5mm and 4.5mm thick.
In the Post to the USA.
Be interesting to hear how they get on.
Last edited by Magna Audio; 28-10-2017 at 22:33.
System: Turntable : SP10 MKII slate plinth, Custom Ebony tonearm board, Arm : Fidelity Research FR64s, Cartridge : SPU Royal N. SUT : Lundahl 1:13. Phonostage : Icon Audio, Streaming RPi/Kali reclocker -> I2S -> DSP XO / Pre / 4 DAC's : WAF Najda, 5 Poweramps : 3 x EL84 SET's, 2 x D class amps on bass channels, Speakers : 5 way front loaded horn system: 2 X Tapped sub 15" LF drivers / 2 X Exponential mid bass 15" drivers / Tractrix 200Hz mid horns with JBL2482's, / Tractrix 550Hz upper wooden horns with factory refurb'd Vitavox S2's / Raal Lazy Ribbons as high frequency tweeters. Wires: good silver or good copper where best suited. DIY RCM.
Maker of tonearm boards, armpods, Tannoy GRF style speaker cabinets, horn speakers, counterweights and more.
For more information about my creations and products please click below
http://fosworld.wixsite.com/magna-audio & on Instagram https://www.instagram.com/magna_audio/
Site Owner/Administrator
Location: Wrexham, North Wales, UK
Posts: 110,012
I'm AudioAl'sArbiterForPISHANTO.
Indeed, Steve, and I suspect that they'll work superbly! I'm sure that Freddy will let us know
Btw, I think you should make a major point of promoting those little ebony spacers, as they often sell for silly prices on ebay, and are useful to lots of folks seeking to obtain more VTA flexibility. Far better too, sonically, than using a thicker T/T mat to make up the same adjustment difference!!
Marco.
Main System
Turntable: Heavily-modified Technics SL-1210MK5G [Mike New bearing/ETP platter/Paul Hynes SR7 PSU & reg mods]. Funk Firm APM Achromat/Nagaoka GL-601 Crystal Record Weight/Isonoe feet & boots/Ortofon RS-212D/Denon DL-103GL in Denon PCL-300 headshell with Funk Firm Houdini/Kondo SL-115 pure-silver cartridge leads.
Paul Hynes MC head amp/SR5 PSU. Also modded Lentek head amp/Denon AU-310 SUT.
Other Cartridges: Nippon Columbia (NOS 1987) Denon DL-103. USA-made Shure SC35C with NOS stylus. Goldring G820 with NOS stylus. Shure M55E with NOS stylus.
CD Player: Audiocom-modified Sony X-777ES/DAS-R1 DAC.
Tape Deck: Tandberg TCD 310, fully restored and recalibrated as new, by RDE, plus upgraded with heads from the TCD-420a. Also with matching TM4 Norway microphones.
Preamps: Heavily-modified Croft Charisma-X. LDR Stereo Coffee. Power Amps: Tube Distinctions Copper Amp fitted with Tungsol KT-150s. Quad 306.
Cables & Sundries: Mark Grant HDX1 interconnects and digital coaxial cable, plus Mark Grant 6mm UP-LCOFC Van Damme speaker cable. MCRU 'Ultimate' mains leads. Lehmann clone headphone amp with vintage Koss PRO-4AAA headphones.
Tube Distinctions digital noise filter. VPI HW16.5 record cleaning machine.
Speakers: Tannoy 15MGs in Lockwood cabinets with modified crossovers. 1967 Celestion Ditton 15.
Protect your HUMAN RIGHTS and REFUSE ANY *MANDATORY* VACCINE FOR COVID-19!
Also **SAY NO** to unjust 'vaccine passports' or certificates, which are totally incompatible with a FREE society!!!
Senior Member
Location: Fredrikstad, Norway
Posts: 236
I'm Chris.
+1 I think ebony spacers, wooden headshell and ebony armboard for my future upgrade
Turntable 1: Technics SL1210M5G/ KAB PSU/ KAB Fluid Damper
Turntable 2: Rega P3 (new) Tangospinner & dual belt/ Rega Neo
Amplifier: Rega Elex-R
RIAA: Rega Fono mk3 & Schiit Mani
Speaker: Klipsch RP280f
Cartridge: Rega Exact & Nagaoka MP-110
Posting Permissions
Reply With Quote
