Hi Darren,
How are the Celestion Ditton 11s as rear speakers? How do they compare to the UL8s? I have a 5.1 system, so no surrounds, but thinking about using either 11s or UL6s for the rear.
...
Type: Posts; User: madders
Hi Darren,
How are the Celestion Ditton 11s as rear speakers? How do they compare to the UL8s? I have a 5.1 system, so no surrounds, but thinking about using either 11s or UL6s for the rear.
...
Hi Andy,
I've been listening to my 25s the last few weeks, trying to decide if it's worth recapping them or not.
I finished the 44s and they sound very good.
I'm not sure how much I can...
Thanks Geoff. And thanks again for the advice. I had another go with the hair dryer earlier. Made it worse again at first, but with a bit of patience I've got it just about perfect.
The speakers...
Hi Darren - yes I've read that a few times, but I didn't look which way round they were before I took them out! I have put them back with the wires at the top, I think it's most likely they were at...
I think it must have been the same before the recap. Something didn't sound right, and this must have been the problem. It's very noticeable on piano music, which I didn't listen to before. But I put...
Wow it worked! Despite removing the screws (luckily they went back in ok). And I completely misunderstood your instructions. First I pulled it up and heated it, and it wouldn't go back down. Then...
Yes the 5" mid - I've attached a couple of pics. I want to try your suggestion with the hair dryer but I can't figure out how to get to the voice coil. I took the three screws out the back, but I...
I've been listening to these for the last couple of days. One speaker sounds excellent (the one I did first). I've realised there is a problem with the midrange driver in the other one. There is a...
I just looked at the back of one of the woofers and there is a foam gasket - I didn't notice it before - it's pretty squashed. There is a faint ring of something round the hole though, so maybe it...
Ah ok thanks! I was thinking about glue to seal them (they already have screws to hold them in place so I don't need clamps I don't think).
I'm glad I asked the question because I almost used some...
It took a lot longer than I expected, but finally finished!
16604 16605
What is the best glue to use when putting the drivers back? I'm pretty sure they were glued in before.
Thanks for the suggestion, I see Wilkos sell it for £1.75. I've already used some Colron teak oil but I'm not impressed with the results and it cost £10! I might redo them.
I ordered the...
Thanks guys. For the mids, I'm sill not sure about the second 6 uF cap. On the PDF it is just a standard Alcap, should I go for a low loss one?
What thickness of speaker cable do you recommend? I...
Hi Jamie,
Thanks! I'll try again with some flux. On some of the connections, there is a lot of solder though!
In your pictures, it looks like you didn't use a low leakage Alcap for the 6 uF in...
Hi everyone,
I recently acquired a pair of Celestion Ditton 25s and 44s that need some work. I've seen a few threads on here about these speakers so I thought I'd start one, and hopefully get some...
Hello! Have you looked at Volumio? You'd need a Raspberry Pi (or something similar), but I think it will do exactly what you're looking for.
Thanks I will check some out! I listen to a lot of 90s music and classical. I also like Fleetwood Mac, First Aid Kit, Rolling Stones, Air, Eurythmics and Lady Gaga of course.
Hi everyone,
I decided to finally create an account here after lurking around the Past Masters forum.
I like vintage hi fi equipment, particularly the 70s Pioneer silver stuff. I've got an...