Tab Content
  • Qwin's Avatar
    14-01-2018, 19:30
    Yes I've used one, liked it a lot till the cantilever just fell out. Paired with a Pro-Ject Phono Box RS and a Trans-fi Audio parallel tracking...
    15 replies | 435 view(s)
  • Qwin's Avatar
    10-01-2018, 12:06
    Qwin replied to a thread Yamaha NS1000M - Tweaks in Past Masters
    . The caps I used in the example above replicate the sound of the original silver cans exactly, if this is what you want then use the Ansar...
    271 replies | 53926 view(s)
  • Qwin's Avatar
    06-01-2018, 21:09
    Qwin replied to a thread Yamaha NS1000M - Tweaks in Past Masters
    I tried using fixed resistors right at the beginning of the project, to be honest, I couldn't hear much, if any difference, one way or the other, so...
    271 replies | 53926 view(s)
  • Qwin's Avatar
    06-01-2018, 20:47
    Qwin replied to a thread Yamaha NS1000M - Tweaks in Past Masters
    As far as I am aware, the design/components never changed, so the response should have been the same throughout its production life. Never seen...
    271 replies | 53926 view(s)
  • Qwin's Avatar
    06-01-2018, 20:44
    Qwin replied to a thread Yamaha NS1000M - Tweaks in Past Masters
    Yes, this is what I was getting at.
    271 replies | 53926 view(s)
  • Qwin's Avatar
    06-01-2018, 12:14
    Qwin replied to a thread Yamaha NS1000M - Tweaks in Past Masters
    Again, I'll put this up for reference. This first plot is of the NS-1000m bass, measured near field to avoid room effects. I've not shown...
    271 replies | 53926 view(s)
  • Qwin's Avatar
    05-01-2018, 21:14
    Qwin replied to a thread Yamaha NS1000M - Tweaks in Past Masters
    Just as a guide for folks, ESR is talked about a lot with re-capping projects, the picture below is of a 1uf electrolytic measured using DATS v2...
    271 replies | 53926 view(s)
  • Qwin's Avatar
    05-01-2018, 20:30
    Qwin replied to a thread Yamaha NS1000M - Tweaks in Past Masters
    The glue almost looks like evostick contact cement, but may be a hot melt of some kind. A couple of mine just cracked out of the glue without a...
    271 replies | 53926 view(s)
  • Qwin's Avatar
    05-01-2018, 20:19
    Qwin replied to a thread Yamaha NS1000M - Tweaks in Past Masters
    The only lytics in the stock crossover are the two in parallel across the bass, all others are film caps. What frequency did you measure these at?
    271 replies | 53926 view(s)
  • Qwin's Avatar
    05-01-2018, 20:16
    Qwin replied to a thread Yamaha NS1000M - Tweaks in Past Masters
    "with this in mind im not touching my ns1000's especially as the caps are glued in." Yes, I had to rip mine apart removing them, that's how I...
    271 replies | 53926 view(s)
  • Qwin's Avatar
    05-01-2018, 20:13
    Qwin replied to a thread Yamaha NS1000M - Tweaks in Past Masters
    If it ain't broke don't fix it! Leave well alone if they are sounding good James. I've been beavering away, doing all kinds of stuff, but...
    271 replies | 53926 view(s)
  • Qwin's Avatar
    05-01-2018, 19:40
    Qwin replied to a thread Yamaha NS1000M - Tweaks in Past Masters
    Thanks Grant, I thought putting it all together in a simple, straightforward form would be useful to folk. I had to stamp on the miss-information...
    271 replies | 53926 view(s)
  • Qwin's Avatar
    05-01-2018, 19:23
    Qwin replied to a thread Yamaha ns1000m in Past Masters
    My active Yamaha has strayed so far away from the original, that I have started a separate project for an active 3-way. Jamie123 - If your looking...
    116 replies | 6229 view(s)
  • Qwin's Avatar
    05-01-2018, 18:59
    Qwin replied to a thread Yamaha NS1000M - Tweaks in Past Masters
    This project has changed a lot during its time, so much so, that it is no longer about the Yamaha NS-1000m or any of its components, so I've started...
    271 replies | 53926 view(s)
  • Qwin's Avatar
    30-12-2017, 16:55
    You can get them from dealers who make speaker leads. Mine have Atlas written on them. These are the boot kind not shrinkable , but look very neat.
    11 replies | 292 view(s)
No More Results

1 Visitor Messages

  1. View Conversation
    1
Showing Visitor Messages 1 to 1 of 1
About Qwin

Basic Information

About Qwin
Name:
Ken
Location::
Durham - UK

Signature


Ken

http://www.jkwynn.co.uk/
DIY Technics/ProJect based Turntable + Terminator linear tracker + Ortofon MC20 Supreme / Pro-Ject Phono box & Pre Box RS / KMTech Active X-Over / Nakamichi AVP1 Power / DIY Sealed Three Way Speakers / Stello CDT100 Transport / DAC Magic.

Statistics


Total Posts
Total Posts
1,379
Posts Per Day
0.75
Visitor Messages
Total Messages
1
Most Recent Message
11-11-2016 04:11
General Information
Last Activity
15-01-2018 08:20
Join Date
15-01-2013
Home Page
http://www.jkwynn.co.uk/